Akia Screens EDGE FREE CLR 4 User Manual

Advertisement

Quick Links

____________________________________________________________________________________________

Product Description:

The Akia EDGE FREE CLR®4 Series is a fixed frame projection screen that uses Akia's EDGE FREE® technology.
The EDGE FREE® design resembles a flat panel TV display. The EDGE FREE CLR
trim to further enhance the frame appearance and absorb projector overshoot.
The screen material included is our CLR
for environments with minimal control over room lighting. It was designed to filter and absorb overhead light while
directing table-top mounted ultra-short throw projection. It best for family rooms, educational facilities, conference
rooms or any applications in which incident light is a factor.

Screen maintenance

Dust, dirt and scratches on the projection screen surface will affect the quality and performance of the projection
image. Follow the instructions below to properly maintain the screen.
1) The screen surface has a horizontal linear structure. DO NOT wipe the screen up and down or in a circular
motion. Wipe gently from left to right only.
2) Clean the dust on the screen surface with a soft brush or microfiber cloth. A rough/coarse towel or cloth may
damage the screen's surface.
3) Gently wipe the screen with a lightly moistened white lint free cloth with water or with a neutral detergent
(1mL/0.33 oz) mixed with water (1000 mL/33.8 oz).
Notes: The following precautions should always be followed to avoid damaging the material, which is
not covered under warranty.
• Don't touch the screen material to avoid leaving fingerprints.
• Use gloves when handling the material.
• Don't scratch the material, as it will leave permanent markings on the screen's surface.
• Don't point to the screen material with a fingertip or other sharp objects to prevent damage to the material.
• Don't use acetone, benzene, alcohol and any other organic solvents to clean the screen material. Using such
chemicals will permanently damage the screen.
12162021JA
Ceiling Ambient Light Rejecting Fixed Frame Screen
®
4, which is an optical lens front projection material precisely formulated
www.akiascreens.com
EDGE FREE® CLR® 4
For model: AK-NB115H-CLR4
USER'S GUIDE
M Type - Version 1
®
4 includes a micro-thin bezel
U-00206
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EDGE FREE CLR 4 and is the answer not in the manual?

Questions and answers

Summary of Contents for Akia Screens EDGE FREE CLR 4

  • Page 1 EDGE FREE® CLR® 4 Ceiling Ambient Light Rejecting Fixed Frame Screen For model: AK-NB115H-CLR4 USER’S GUIDE M Type - Version 1 ____________________________________________________________________________________________ Product Description: The Akia EDGE FREE CLR®4 Series is a fixed frame projection screen that uses Akia’s EDGE FREE® technology. ®...
  • Page 2 1. Frame and Edge Trim Parts List 2 pcs 2 pcs Main Frame Parts Edge Trim Parts Item item vertical frame Part A. Part D. ½ horizontal frame Part B. Part E. ½ horizontal frame Part C. Part F. 2. Hardware Parts List M4*4 D5*4 M4*4...
  • Page 3 Item Parts List 115’’ Center Joints- M4 (bottom position) Center Joints-D5 (top position) Elbow Joints M4 (bottom position) Elbow Joints D5 (top position) M4x7 Screws Spring Spring Hook wall brackets Φ5x50 Wall Screws Hollow Wall anchors M4x4 Screws Angle cover Center Support Bar White gloves Spring...
  • Page 4 Step 5: Secure the elbow joints by fastening them with M4x7 screws (g), 4 at each corner. Screen Material CAUTION! THE PROJECTION FABRIC IS A DELICATE OPTICAL/LENTICULAR SCREEN MATERIAL AND SHOULD NOT BE FOLDED, BENT, OR CREASED. ALWAYS MAINTAIN SCREEN MATERIAL FLAT AND TAUT DURING SETUP AND DISASSEMBLY.
  • Page 5 Center Support Bar Step 8: Insert the Center Support Bar (o) into the upper top groove on the back of the frame with the bottom end near the approximate center point of the frame and rotate it in at an angle so that both ends of the bar are in alignment with the groove.
  • Page 6 Note (after all springs have been attached): Correct material installation –Corners of the screen material are properly wrapped around the corner edges of the frame and material is evenly tensioned and flat, creating a nicely taut surface. How to avoid getting ripples on the screen’s material surface Solution: With the gloves on and assuring they are clean, pull and smooth out the material using your hand from the center to the corners, creating a nicely taut surface as shown below.
  • Page 7 Step 11: Install the angle cover (n.) on each corner of the frame using the double-sided tape. Tear off the double-sided tape. Step 12: Install the springs (h) in each middle area to further support the bezel trim screen Notice to Installer: ®...
  • Page 8 Wall Installation Step 12: Measure the overall length and height of the frame and drill holes for the top brackets. Line up the wall brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver. If not installing into a structural wood stud, use a hollow wall anchor then screw in the M5x50 wood screws with a screwdriver.

Table of Contents