Advertisement
Quick Links
Installing the Balanced Body
Studio Reformer with Twist Lock and Metal Riser
The Konnector is compatible with Balanced Body Studio
Reformers with metal risers and removable shoulder rests
ONLY. If you aren't sure whether this system will work with your
equipment, please contact Balanced Body at 1-800-PILATES (US
and Canada), or +1-916-388-2838 (all other countries).
To view the installation podcast, please visit
www.pilates.com/instructions
TOOLS REQUIRED (NOT INCLUDED):
» Power Drill
» Tape
PARTS LIST (INCLUDED):
ITEM
Konnector Rope
Tri-Loops (Grey)
Tri-Loops (Black) with pulleys
Konnector Metal Riser Assembly
Left Pulley Bracket Assembly
Right Pulley Bracket Assembly
Pulley Spring Assembly
Twist Lock™ Shoulder Post
Twist Lock Flanged Cap
Hair Guard
Bolt/Washer/Nut Assembly
2-3/4" Allen bolts
1/4-20x3/8" Button head screw
1/4-20x1-1/2" Flat head screw
1/4" Flat Washer
1/4" Fender Washer
1/4-20 Nylock nut
5/32" Allen wrench
3/16" Allen wrench
5/16" Drill Bit
Drill Template
7/16" Wrench
WARNING: Using the existing shoulder posts with a Konnector
system can cause the loops to fall off the posts during use
which may cause injury.
REMOVE ROPES, POST AND SHOULDER BRACKETS
1. Remove the ropes and loops from your Reformer, they are no
longer needed.
2. Unthread each post from the shoulder rest bracket by hand
and completely remove them from the shoulder rest bracket.
You will no longer need them. Remove the shoulder rest
bracket from the carriage. Repeat on the other side.
3. Using the provided Allen wrench, remove the two flat head
screws as shown in Figure A. Replace these two removed
PART NO.
QTY
screws with the two flat head screws (1/4"-20 x 1-1/2" long)
210-075
1
provided.
210-061
1
210-060
1
N/A
2
N/A
1
N/A
1
N/A
2
616-400
2
616-401
2
616-187
1
N/A
2
GEN8032
4
Figure A
GEN9943
4
GEN7313
2
GEN9305
6
GEN9952
2
GEN9021
4
GEN9282
1
GEN9280
1
TOL1059
1
607-541
1
616-113
1
Konnector
®
WARNING: If you are only using some of the loops, the
unused loops MUST be stored on the flanged shoulder
posts.
1
™
2
3
Contact Us
1-800-PILATES | +1-916-388-2838
pilates.com | info@pilates.com
400-441 | 03.22.19
4
Advertisement
Related Manuals for Balanced Body Konnector
Summary of Contents for Balanced Body Konnector
- Page 1 Studio Reformer with Twist Lock and Metal Riser The Konnector is compatible with Balanced Body Studio WARNING: Using the existing shoulder posts with a Konnector Reformers with metal risers and removable shoulder rests system can cause the loops to fall off the posts during use ONLY.
- Page 2 INSTALL THE HAIR GUARD AND CARRIAGE PULLEY BRACKETS 4. Bolt the hair guard to the two Circular holes carriage pulley brackets using the 1/4-20x3/8” long Slotted holes flanged button head screws. Make sure the Threaded holes threaded holes Figure E are facing inward, and the hair guard is aligned as in...
- Page 3 21.Install the Pulley Spring Assembly as shown in Figure J. There will be one plastic spacer on both sides of the pulley spring, one will be against the side of the wood, and on the outside frame, a washer, nut then acorn nut. INSTALL RISERS 22.Remove the metal risers from your existing reformer by removing the detent pins that go through the risers.
- Page 4 Figure O IMPORTANT SAFETY NOTE: Use of the Konnector system in a manner for which it is not intended may result in equipment damage and/or injury to the user. Intense cardio work utilizing jarring movements may overload the system. Balanced Body is not responsible for injuries caused by equipment misuse.