Related Manuals for Producer's PRIDE 1237322
Summary of Contents for Producer's PRIDE 1237322
- Page 1 SKU: 1237322 Garden Chicken Coop (77.5 in. L * 50.1 in.W *74.8 in.H) Distributed by: TRACTOR SUPPLY COMPANY 5401 VIRGINIA WAY, BRENTWOOD, TN 37027 For customer support, call: 1-888-376-9601 www.TractorSupply.com MADE IN CHINA...
-
Page 2: Care Instructions
CARE INSTRUCTIONS SAFETY INFORMATION: WARNING : Please keep children out of assembly area during assembly. WARNING: This product is designed exclusively for chickens. Not intended for children. BEFORE YOU BEGIN: Read instruction prior to assembly. This product contains parts that can be damaged if incorrectly assembled. - Page 3 PARTS LIST Part Image Description Quantity Front&Back run panel 2pcs Front&Back short run 2pcs panel Left run panel 1 pc Right run panel Side panel of flower box 2pcs...
- Page 4 Front panel of flower Back panel of flower Floor panel of flower Back Coop Panel Front Coop Panel...
- Page 5 Right side panel of nesting box Left side panel of coop Drawer base frame Drawer Side panel of nesting 2pcs Back panel of nesting Floor of nesting box...
- Page 6 Roosting bar 2pcs Divider panel 3pcs Ladder Roof cap Nesting Box Lid with hinges Roof panels 2pcs Support bar 4pcs Screws 50mm 14+1pcs...
- Page 7 Screws 40mm 40+2pcs Screws 35mm 8+1pcs Screws 30 mm 6+1pcs Screws 35 mm 12+1pcs Screws 14 mm 22+1pcs Support arm 1pair Door latch Liner...
- Page 8 CAUTION: If using a cordless power drill / screwdriver, turn torque setting down to a minimum level to start so that screws are not stripped. Adjust torque up slightly if needed to fully tighten screws. ASSEMBLY INSTRUCTION Front&Back run panel (1) Front&Back short run panel Step 1: Attach the and the...
- Page 9 Step 3: Attach the Back Coop Panel (9) with the Right side panel of nesting box (11) and the Left side panel of coop (12) using screws(B)*6pcs. Then also attach the Front coop panel (10) using screws(B)*6pcs as shown. Step 4: Place the Drawer base frame (13) into the coop as shown.
- Page 10 Step 5: Next, using two people, place the assembled coop on top of the chicken run as shown in the picture below and secure in place with screws (A). Next, lift the assembled flower box on top of the chicken run and secure in place with screws (A) as shown in picture below.
- Page 11 Back panel of nesting box (16) Step 7: Attach the to the side panels of nesting box using the screws(B)*4pcs. Floor panel of nesting box (17) Step 8: Place the into the nesting box, and then secure nesting box to chicken run frame with screws (A) as seen in picture below. *** Note: Chicken run door must be open to install the two screws directly below the nesting as seen in picture below.
- Page 12 Step 9: Attach the flower box to the coop using screws(D)*2pcs as shown. And then place the liner into the flower box. ***Note: Liner is designed with small openings at one end. This end should be placed at the lower end of the flower box to allow water to drain out. The liner can be stapled in place before filling with dirt to help keep form.
- Page 13 Mount the Nesting Box Lid with hinges(22) Step 11: to the coop using screws(F) *4pcs as shown. Support arms (G) Step 12: Open the nesting roof, and attach the using screws(F) Nesting latch (H) using screws (F)*6pcs as shown. *8pcs. Then, assemble the ***Note the support arms must be installed so that hinge folds to the inside when installed properly.
- Page 14 Step 13: Locate both Roof panels (23) and position them on the ground with wooden frame side up as seen in the picture below. Next place the wooden Support bars (24) in place on the wooden frames (see picture below) and secure in place with 3 screws each (E).
- Page 15 Roof cap (21) Drawer Step 14: Attach the using screws (B)*4pcs. Finally, place the (14) into the coop as shown. Finished Coop...