Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Producer's PRIDE Hill Country Coop
Summary of Contents for Producer's PRIDE Hill Country Coop
- Page 1 SKU: 1277537 Hill Country Coop (114 in. L x 57.8 in. H x 56.3in. W) Distributed by: TRACTOR SUPPLY COMPANY 5401 VIRGINIA WAY, BRENTWOOD, TN 37027 For customer support, call: 1-888-376-9601 www.TractorSupply.com MADE IN CHINA...
- Page 2 CARE INSTRUCTIONS SAFETY INFORMATION: DANGER: Please keep children out of assembly area during assembly. WARNING: This product is designed exclusively for chickens. Not intended for children. BEFORE YOU BEGIN: Read instruction prior to assembly. This product contains parts that can be damaged if incorrectly assembled.
- Page 3 PARTS LIST Part Image Description Quantity Roof cap Top roof panel 2pcs Nesting roof Back coop panel Front coop panel Right coop panel...
- Page 4 Left coop panel Right & left nesting 2pcs panels Nesting floor Back nesting panel Drawer Run side panel 1 Run side panel 2...
- Page 5 Run side panel 3 Run side panel 4 Run side panel 5 2pcs Right run panel Run left cover panel 2pcs Run right cover panel Roosting bar for run 2pcs...
- Page 6 Roosting bar 3pcs Nesting box divider 2pcs Support bar 4pcs Screws 3*16mm 12+1pcs Screws 3.5*35mm 20+1pcs Screws 3.5*40mm 56+1pcs Screws 3.5*60 mm 12+1pcs Door pull lever Support arm 1pair...
- Page 7 CAUTION: If using a cordless power drill / screwdriver, turn torque setting down to a minimum level to start so that screws are not stripped. Adjust torque up slightly if needed to fully tighten screws. ASSEMBLY INSTRUCTION Step 1: Attach the right coop panel (6) to the run side panel (12) (13) using screws (B)*4pcs.
- Page 8 Step 3: Attach the back coop panel (4) to the left and right coop panel using screws (C)*6pcs as shown. Step 4: Place the roosting bars (21) in the coop, Using screws (B)*2pcs as shown.
- Page 9 Step 5: Attach the right and left nesting panels (8) using screws (B)*6pcs as shown. Step 6: Place the nesting floor (9) inside the nesting box. And then install the nesting box divider (22) as shown.
- Page 10 Step 7: Attach the back nesting panel (10) to the nesting panels using screws (C)*4pcs as shown. Step 8: Attach the nesting roof (3) to panel using screws (A)*4pcs as shown.
- Page 11 Step 9: Open the nesting roof and attach the support arms (F) to the nesting roof panels using screws (A)*8pcs. Note the left and right direction of the support arms. Step 10: Attach the run side panels (14) (15) (16) to each other using screws (D)* 12pcs as shown.
- Page 12 Step 11: Attach the right run panel (17) to the run side panels using screws (C)*6pcs as shown. Place the roosting bar for run (20) as shown and secure using screws (C)*4pcs. Step 12: Attach the run left cover panel (18) and the run right cover panel (19) to the run side panels using screws(C)*14pcs as shown.
- Page 13 Step 13: Place the support bar (23) to the top roof panels (2) using screws (C)*12pcs as shown. Then place the roof on the top of coop and secure in place using screws (B)*8pcs. Step 14: Attach the roof cap (1) using screws (C)*4pcs as shown. Place the door pull lever (E) through hole in panel and secure into place by threading into door hardware...
- Page 14 Step 15: Place the drawer (11) as shown. Finished Coop...
Need help?
Do you have a question about the Hill Country Coop and is the answer not in the manual?
Questions and answers