Safety Important - Please read these instructions fully before starting assembly • WARNING: To prevent • Warning: This unit weighs possible overbalancing this unit approximately 49kgs. must be secured to a wall using Please lift with care. the 2 overbalance protector kits •...
Cabinet Panels 1 73.3 x 42.9cm 2 73.3 x 42.9cm 3 73.3 x 41.5cm 4 120 x 45cm 6 117.6 x 70.1cm x 10 5 57.55 x 6cm Drawer Panels Note: the internal drawer panels are grey 7 59.45 x 18.9cm 8 59.45 x 18.9cm 9 40 x 14cm 40 x 14cm...
Page 4
Fittings Use these drawings to correctly identify the fittings Bag 1 x 16 x 26 x 19 x 12 x 24 Bag 2 x 12 x 24 x 12 x 12 x 24...
Page 5
Fittings x 12 Tools Only used for drilling walls...
Page 6
Fitting Ball Bearing Runners www.youtube.com/watch?v=yG4xtiJJeSg Bag 1 x 12 x 16 x 26 x 19 x 12 x 24 2nd hole 2nd hole...
Page 15
Squaring up a Chest and fitting the Back Panel www.youtube.com/watch?v=FeaI6541z7o The Back panel must be flush with the Back Rail. A = B Make sure measurement A and B are the same...
Page 16
Only use 1 Screw to fit each Bracket IMPORTANT: The Back panel must slot into the groove in the Top panel...
Page 19
WARNING! In order to prevent overturning this product must be used with the 2 wall attachment devices provided See the next section for a guide to wall mounting and fixings Slide the Brackets against the wall. Fit the 2nd screws supplied with the Brackets into the underside of the Top panel.
A Guide to Wall Mounting & Fixings Important: When drilling into walls always Important note: check that there are no hidden wires or pipes etc. If plastic wall plugs Make sure that the screws and wall plugs being used are supplied with your are suitable for supporting your unit.
Drawer Assembly Bag 2 Warning: Glass! Handle with care x 12 x 24 x 12 x 12 x 24 Drawer Assembly www.youtube.com/watch?v=InNBV_uuMmo x 12 x 12 Right-Hand Drawer Front I.D. hole x 12...
Page 23
x 12 Before securing the Drawer Base, make sure it is inserted in all 4 grooves. You may need to manoeuvre it slightly.
Page 24
Important: Make sure that the drawer assembly is square before fitting the wedgefixes. x 24...
Page 25
Fitting Ball Bearing Runners www.youtube.com/watch?v=yG4xtiJJeSg I.D. hole R i g h t - H D r a a n d w e r F r o Warning: Use a Screwdriver to position the Runners as they could have sharp edges Starting with the bottom Right-Hand Drawer and working your way up, slide both of the Runners forward and locate the Drawer Sides between them, lining up the holes in the Drawer Sides with the 2nd 'threaded' holes in the Runners.
Page 26
Fitting Ball Bearing Runners www.youtube.com/watch?v=yG4xtiJJeSg L e f t - H D r a a n d w e r F r o Warning: Use a Screwdriver to position the Runners as they could have sharp edges Starting with the bottom Left-Hand Drawer, slide both of the Runners forward and locate the Drawer Sides between them, lining up the holes in the Drawer Sides with the 2nd 'threaded' holes in the Runners.
Page 27
Assembly is complete Please remove any blue protective film from panel edges and clear protective film from panel surfaces and clean the mirrors...
Need help?
Do you have a question about the Home Jenson 926/9567 and is the answer not in the manual?
Questions and answers