Directed Directechs DS4+ Installation Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Accessories
  5. DS4+
  6. Installation manual
Directed Directechs DS4+ Installation Manual

Directed Directechs DS4+ Installation Manual

Hide thumbs Also See for Directechs DS4+:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION GUIDE
SUBARU2
Designed by Installers for Installers
© 2017 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
2017-11-21
DS4+

Advertisement

Table of Contents
loading

Related Manuals for Directed Directechs DS4+

Summary of Contents for Directed Directechs DS4+

  • Page 1 SUBARU2 Designed by Installers for Installers © 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.

  • Page 2: Table Of Contents

    Contents Warning! Safety first ........................3 Introduction ............................ 4 Pre-installation and application warnings ..................4 Vehicle application guide ......................5 Wiring connections ......................... 6 Main harness (H1), 12-pin black connector .................. 6 Relay harness (H2), 10-pin white connector .................. 6 Data harness (H3), 8-pin white connector ..................

  • Page 3: Warning! Safety First

    The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.

  • Page 4: Introduction

    Keysense connection is ONLY needed if keysense is not recognized through data at the time of programming. See LED diagnostics & Troubleshooting section for more details. Additional parts required (maximum required): Resistor 100Ω Fuse 7.5A Diode 6A 0 x 1A Diodes 0 x Resistor 0 x Fuse 2 x Relay DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.

  • Page 5: Vehicle Application Guide

    DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.

  • Page 6: Wiring Connections

    (MUX) Analog Input/Output H3/7 Orange/Black Immo. Data H3/8 Yellow/Black Keyless Data If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.

  • Page 7: Analog Input/Output Harness (H4), 22-Pin White Connector

    If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.

  • Page 8: Installation (Wiring Diagrams, Fuse Selection & Vehicle Wiring Reference Charts)

    It is important to check that the (+) 12V: 34 33 Pin 4 Ignition Switch) fuses are positioned correctly. Immo. Data: Pin 31 (+) Ignition 2: Pin 6 (+) Starter 2: Pin 7 DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.
  • Page 9 HS CAN High Data BBCM (B), behind the fuse box. White HS CAN Low Blue Data BCM (B), behind the fuse box. White Parking Lights Lt. Green BCM (B), behind the fuse box. White DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.
  • Page 10 HS CAN High Data BCM (B), behind the fuse box. White HS CAN Low Blue Data BCM (B), behind the fuse box. White Parking Lights Black/Blue BCM (B), behind the fuse box. White DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.

  • Page 11: Type 2

    Ignition Switch) 64 63 62 61 60 59 58 57 56 55 behind fusebox) (+) Starter 2: Pin 7 (White bottom conn. passenger side underhood) (+) Keysense: pin 10 DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.
  • Page 12 Security Light Brown/Yellow BCM (K), rear of the fuse box. White Parking Lights Black BCM (K), rear of the fuse box. White Immo. Data White/Blue ECM, passenger side underhood bottom connector. White DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.
  • Page 13 Locating components in the vehicle B281 DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.

  • Page 14: Type 3

    Pin 4 Immo. Data: White/Lt. Blue, pin 31 (+) Starter 2: (+) Accessory 2: White/Orange or Pin 5 White/Green, pin 6 Ignition conn. (White conn. at Ignition Switch) DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.
  • Page 15 HS CAN High Data BCM (B), right of steering column. White HS CAN Low Blue Data BCM (B), right of steering column. White Parking Lights Black/White BCM (B), right of steering column. White DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.
  • Page 16 (+) Key Release 1: pin 4 DS4+ (right of steering column) Locating components in the vehicle (right of steering column) 7 6 5 4 3 16 15 10 9 23 22 21 20 33 32 DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.

  • Page 17: Key2Go

    Any first-time user must re-register to gain access to Key2GO, and some additional information will be required to complete the registration process, such as your Directed account number and store name. Key2GO is compatible with XKLoader2, the online web tool, and the DirectLink Mobile application.

  • Page 18: When Used In Conjunction With Smartstart

    SmartStart. To ensure proper functionality with SmartStart, it is important that it is selected in the system programming of the DirectLink application or via the online web tool. Note: Both black D2D ports are reserved for the Control Center (antenna) and 8504D Combo Sensor. DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.

  • Page 19: Module Programming

    By default, the tachometer is preprogrammed for the vehicle. For instructions on how to Initialize tachometer program tach, see page 23. * Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.

  • Page 20: Led Diagnostics And Troubleshooting

    External module synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.
  • Page 21 The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 Analog error codes Description Troubleshooting DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. Flashes red, green & orange DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.

  • Page 22: Soft Reset

    After 3 seconds the LED turns ON solid orange. Keep holding the programming button until & & the LED flashes red, then orange slowly. Solid Hold Flashes Release the programming button. The LED turns ON solid red. & Release Solid DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.

  • Page 23: Learning The Tach (Not Needed With Virtual Tach)

    Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature using the DirectLink application for mobile devices to adjust the starter output time in 50mS increments to compensate for such an occurrence. DS4+ SUBARU2 © 2017-11-21 Directed. All rights reserved.

  • Page 24: Limited Lifetime Consumer Warranty

    Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;...

  • Page 25: Quick Reference Guide

    Factory remote. Press the Remote Start button on the transmitter.* • Aftermarket remote. • Directed SmartStart application via your smartphone. & The parking lights will flash once to indicate the Parking lights flash x1 Press Remote vehicle is now in Pit Stop Mode.
  • Page 26 The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.

Table of Contents