Related Manuals for Grouser Products 450
Summary of Contents for Grouser Products 450
- Page 1 12-20 (V6) Blade - 450-660 Owner’s Manual & Parts Book Purchase Date Serial Number Model Number Tractor Model Dealer PN: 63-17732 Date 5-3-2014...
- Page 2 Warning When using the dozer blade, pay special attention to the area between the blade and the hood of the tractor. In the right conditions, material can build up. Grouser Products is not responsible for careless operation of the blade.
- Page 3 4. Make sure the area is clear of people before moving any equipment. 5. Do not modify or permit anyone else to modify or alter the equipment and its components without first consulting Grouser Products. Servicing the Dozer: 1. Read and follow all safety instructions provided by the tractor manufacturer.
- Page 4 Angle / Tilt Function Abbreviation Key HAHT Hydraulic Angle - Hydraulic Tilt 6-Way HANT Hydraulic Angle - No Tilt 4-Way NAHT No Angle - Hydraulic Tilt 4-Way NANT No Angle - No Tilt 2-Way Torque Specifications All bolts should be tightened to the specifications that are stated. If specifications are not stated, follow torque charts below.
- Page 5 Skid Shoe and Tilt Plate Adjustment Skid Shoe Adjustment: 1. Adjust ratchet on skid shoe mount to get skid shoe to desired height. Skid Shoe Ratchet 2. When skid shoes are worn down, replace with new skid shoes. Tilt Plate Adjustment: 1.
- Page 6 Hydraulic Instructions Prior to operating the blade, bleed all air out of the hydraulic system. Start with the furthest location away from the remote until all air is out. Hydraulic Angle System Operating Instructions If your Grouser blade was purchased with the Hydraulic Angle Option, you will have the ability to angle the blade 30 degrees left or right.
- Page 7 If the angle system is not used correctly, frame damage may occur. Some damaged frames can be repaired, please contact Grouser Products for repair instructions if needed. Please contact Grouser Products with any questions by: Phone - 701-282-7710 or 800-747-6182;...
- Page 8 Initial System Startup Start the tractor and run the blade thru all the functions. If any function does not work properly, bleeding of the system may be required. If problem still persists, call Grouser Products.
- Page 9 3/4” ID - Non Rotating Pin Spacer Bushing 19-13525 2.75 x 2.50 x 4.75 Spring Bushing 26-34738 4x20 Long Cylinder - Bushed Tube Ends (647267) 32-14060 450 LP Lift Frame 32-12910 660 LP Lift Frame 34-14961 Manual Canister 43-13025 Pin Weld (Lift Frame / UC) 43-5033 Pin Weld (Lift Cyl.
- Page 10 66” x 1/2” -8JIC/-8JIC Hose 35-30134 75” x 1/2” -8JIC/-8JIC Hose 35-30160 288” x 1/2” -8JIC/-8JIC Hose 70-20807 3/4” Hex Jam Nut NF Item #A for 450 and Item #B for 660 Dozer Welded to front of frame Hoses Not Drawn To Scale...
- Page 11 NOTE: When ordering cylinder seal kits, the part number Item Qty. Part No. Description on the cylinder is needed. The number is stamped on the base end of the cylinder opposite of the hydraulic ports. 16-20036 5/16” x 1-1/2” Hex Bolt Gr 5 NC No.
- Page 12 Some Parts Hidden For Clarity Item #A for HAHT & HANT and Item #B for NAHT & NANT Item No. Qty. Part No. Description 11-3049 Bell Crank Weld 16-20125 1/2” x 1-1/4” Hex Bolt Gr 5 NC 16-20132 1/2” x 3” Hex Bolt Gr 5 NC 16-20560 1”...
- Page 13 Qty 2.
- Page 14 Item Qty. Part No. Description 11-5055 450-660 Series Stabilizer Arm 11-8082 450-660 Series Angle Arm Right 11-9039 450-660 Series Angle Arm Left 14-9366 Non Tilt Bar 16-20036 5/16” x 1-1/2” Hex Bolt Gr 5 NC 16-20132 1/2” x 3” Hex Bolt Gr 5 NC 16-20424 1/2”...
- Page 16 Hoses Not Drawn To Scale...
- Page 17 Configuration HAHT HANT Item No. Part No. Description Qty. Qty. 16-20036 5/16” x 1-1/2” Hex Bolt Gr 5 NC 16-20043 5/16” x 3-1/4” Hex Bolt Gr 5 NC 18-3074 Hose Hold Down Clamp 18-3075 Hose Hold Down Clamp Plate 18-15684 12-20 - HAXT Hose Hold Down Plate 18-8973 Coupler Mounting Bracket...
- Page 18 Hoses Not Drawn To Scale...
- Page 19 Item No. Qty. Part No. Description 16-20035 5/16” x 1” Hex Bolt Gr 5 NC 16-20036 5/16” x 1-1/2” Hex Bolt Gr 5 NC 16-20040 5/16” x 2-1/2” Hex Bolt Gr 5 NC 18-14695 Bracket, Relief Valve 18-3074 Hose Hold Down Clamp 18-3075 Hose Hold Down Clamp Plate 18-8973...
- Page 20 Item Item Qty. Part No. Description Qty. Part No. Description 16-20036 5/16” X 1-1/2 “ Hex Bolt Gr 5 NC 35-11686-1390 139” x 3/8” -8JIC/-8JIC Hose 16-20047 5/16” X 4-1/2 “ Hex Bolt Gr 5 NC 35-11686-1610 161” x 3/8” -8JIC/-8JIC Hose 16-20218 3/4”...
- Page 21 See Page 25 for hydraulic schematic. Item Hoses Not Drawn To Scale Qty. Part No. Description 16-35C612 3/8” x 3/4” Flanged Bolt 18-14737 700 Series Female Coupler Mount - Universal 25-34342 Tappet Quick Coupler Male - Poppet Style 25-34321 Tappet Quick Coupler Female 25-3403 Pioneer Dust Cap Slider (Blue) - Left Side Cylinder 25-3404...
- Page 22 Item Qty. Part No. Description 15-17570 12-20 XAXT (V6) - Blade Weld 15-16855-L 12-20 Blade End Weld Left 15-16855-R 12-20 Blade End Weld Right 16-16305 3/8 x 1.25” Flanged Elevator Bolt 16-20517 3/4” x 4-1/2” Hex Bolt Gr 8 NC 16-20538 7/8”...
- Page 23 Item Qty. Part No. Description 34-16429 12-20 10” UHMW 34-17565 Ratchet Jack 44-16977 12-20 Standoff Shim 44-16525 12-20 Standoff (1.25” x 2”) 44-15600 12-20 Custom Name Plate - (6.2” x 25.6”) 44-15605 Ag Pro 12-20 Name Plate - (6.2” x 25.6”) 44-16401 12-20 Plate, Top Cover Right 44-16402...
- Page 24 Item Qty. Part No. Description 15-17590 NANT - Blade Weld 12-20 Slider (V6) 16-20542 7/8” X 3” Hex Bolt Gr 5 NC 44-16470 Box End Plate 12-20 Slider 44-16480 Silage Box End Plate 12-20 Slider 57-20758 7/8” SAE Hardened Flat Washer - 1-3/4” OD 70-20598 7/8”...
- Page 28 If such equipment is found to be defective within one year, it is the obligation of Grouser Products under this warranty to repair or replace (exclusive of the cost of labor and transportation), any equipment or parts, in the judgment of Grouser Products to be defective in material or workmanship.
Need help?
Do you have a question about the 450 and is the answer not in the manual?
Questions and answers