Related Manuals for MEI Cashf low SC83
Summary of Contents for MEI Cashf low SC83
- Page 1 MEI Cashflow SC83 Installation & Operation Manual ©MEI Inc. 2007 MEI CASHFLOW SC83 Page-1 www.meigroup.com Part # 252055088 G3...
- Page 2 MEI CASHFLOW SC83 Page-2 www.meigroup.com Part # 252055088 G3...
- Page 3 MEI has made every effort to ensure that the information in this document is accurate. MEI disclaims any liability for any direct or indirect losses (how so ever caused) arising out of use or reliance on this information.
-
Page 4: Table Of Contents
©Mars Inc. 2004 MEI is a trademark of Mars, Inc. Information is subject to change without notice. MEI has made every effort to ensure that the information in this document is accurate. However, we cannot be held responsible for any errors or omissions. -
Page 5: Model Number
04- Opto Isolated EBDS* 07- RS232 EBDS* Secure Cashbox 83mm note path. * EBDS is a MEI protocol. EBDS stands for Extended bi-directional serial. Note: Other interfaces will also be supported. Serial Number W W Y L C C # # # # #... - Page 6 OVERVIEW COMPONENTS Acceptor Module Chassis Cashbox MEI CASHFLOW SC83 Page-6 www.meigroup.com Part # 252055088 G3...
-
Page 7: Features
POWER MOUNTING SC83 CONFIGURATION BUTTON NOT USED ON SERIES DIAGNOSTIC LEDS SEE PAGE FOR DETAILS USB SERVICE PORT SEE PAGE AND FIGURE FOR DETAILS ACCEPTOR USER INTERFACE FLEXIBLE HANDLE PASSIVE CASHBOX LATCHES MEI CASHFLOW SC83 Page-7 www.meigroup.com Part # 252055088 G3... -
Page 8: Main Components Of The Sc83 Note Acceptor
Not all entry guides fit in every machine. Your choice regarding entry guides will depend on machine specifications. Below are three entry guides that MEI currently manufactures. For customers who prefer to tool their own entry guide, please contact our technical department. -
Page 9: Installing The Chassis
Use star washers when mounting the chassis via the back or side mounting options. If the side mounting option is selected, use the lower mounting holes with an M4 screw to ensure a bonded connection to the host machine. MEI CASHFLOW SC83 Page-9 www.meigroup.com Part # 252055088 G3... -
Page 10: Inserting And Removing The Acceptor Module
• To remove the unit, pull upwards on the release lever located on the front of the Acceptor Module and pull away from the chassis. Acceptor Module MEI CASHFLOW SC83 Page-10 www.meigroup.com Part # 252055088 G3... -
Page 11: Installing An Entry Guide
(refer back to chassis installation instructions). • To remove an entry guide, slide a flat head screwdriver between the entry guide and the acceptor module. (as shown in the diagram on the right) MEI CASHFLOW SC83 Page-11 www.meigroup.com Part # 252055088 G3... -
Page 12: Installing The Cashbox
Placing your thumb at this location will give you sufficient leverage to remove the cashbox. LACE HUMB MEI CASHFLOW SC83 Page-12 www.meigroup.com Part # 252055088 G3... -
Page 13: Installing Locks On The Cashbox
Locks vary greatly in price, security, keying policies, etc. The customer is responsible for selecting a lock with performance that is fit for the intended purpose. MEI does not test or endorse any specific brand of lock for security characteristics. For applications requiring NO locks, a non- secure “slam”... -
Page 14: Updating Software
(CPM). Installation of a PROM will disable the ability of the programing module (CPM) to communicate with the note acceptor. Future software changes can only be made by replacing the PROM (chip change). MEI CASHFLOW SC83 Page-14 www.meigroup.com Part # 252055088 G3... - Page 15 3 times = program error CPM on CPM busy (Do not disconnect CPM) upgrade ☺ complete (Disconnect CPM) battery low wrong product connected bill reader error CPM error program error MEI CASHFLOW SC83 Page-15 www.meigroup.com Part # 252055088 G3...
- Page 16 The cover will be released once the cover has cleared the black ramps as shown in the diagram below. 4. Once the yellow cover is released in the front, slide it back and remove it. MEI CASHFLOW SC83 Page-16 www.meigroup.com Part # 252055088 G3...
-
Page 17: Replacing The Prom
Replacing the yellow cover Note: To install the yellow cover, the acceptor module must remain open. 7. To re-install the yellow cover, align the cover back to the position shown below. MEI CASHFLOW SC83 Page-17 www.meigroup.com Part # 252055088 G3... - Page 18 9. Close the acceptor module and re-install it into the chassis. 10. If the power is on, the unit will power up and perform a run and stack. MEI CASHFLOW SC83 Page-18 www.meigroup.com Part # 252055088 G3...
-
Page 19: Harnessing And Connectors
———— NOTES: RXD refers to input to the note acceptor. TXD is an output. Pins 12 and 5 are tied with a loop of wire in back of the 12-pin connector. MEI CASHFLOW SC83 Page-19 www.meigroup.com Part # 252055088 G3... -
Page 20: Maintenance
The SC83 series note acceptor was designed not to require calibration. Thus, the unit has no switch settings or calibration mode that allows a user to perform a calibration. Calibration may only be performed by MEI trained technicians. MEI CASHFLOW SC83 Page-20 www.meigroup.com... -
Page 21: Troubleshooting
Note: By opening the machine door, you will disable the primary interface. The 10-second delay allows you to see a normal condition on the unit prior to the MMI display update. MEI CASHFLOW SC83 Page-21 www.meigroup.com Part # 252055088 G3... -
Page 22: Frequently Asked Questions
What is a CPM (Cashflow Programming Module) and how does it work? A CPM is a yellow handheld device that is programmed by MEI and is used to download software into a CASHFLOW SC83 Flash units. The CPM consists of a yellow button, a red and green LED and 2 USB connectors. - Page 23 Note 1: Opening the machine door will disable the primary interface. The 10-second delay is to allow the technician to see a normal condition on the unit prior to the MMI display update to disabled. MEI CASHFLOW SC83 Page-23 www.meigroup.com...
- Page 24 SC8302 P is a PROM unit made to interface to IGT’s Netplex machines. It uses the IGT ID024 interface. SC8304 is a Flash unit made to interface to various machines. It uses MEI Opto Isolated EBDS Interface. SC8304 P is a PROM unit made to interface to various machines. It uses MEI Opto Isolated EBDS Interface.
- Page 25 SC83 unit does not have any dip switches. Notes can be enabled and disabled by using a configuration coupon. Contact MEI for more information. What is the purpose of the red, black and white wires that come out of the main...
- Page 26 Who can I contact for service on a CASHFLOW SC83? M E I Unit 51/52, Suttons Business Park Suttons Park Avenue Early, Redding RG6 1AZ United Kingdom Internet: http://www.meigroup.com MEI CASHFLOW SC83 Page-26 www.meigroup.com Part # 252055088 G3...
-
Page 27: Sc83 Dimension Drawings
DRAWINGS MEI CASHFLOW SC83 Page-27 www.meigroup.com Part # 252055088 G3...