Kwikset HomeConnect 620 Installation And User Manual page 4

Home Connect 620 at a Glance
Interior (cover removed)
Exterior
1-touch
locking
button
Keypad
Keyway
SmartKey
tool hole
Note: When the cover is
removed, the turnpiece shaft
can be used to manually
lock and unlock the door.
Troubleshooting
A complete Programming and Troubleshooting
Guide is available on the Home Connect 620
page at www.kwikset.com/support.
Operating Your Lock
Locking Unlocking
Press and release .
Enter user code on the keypad.
Note: If you press an incorrect key,
press
and enter your user code again.
Mute/Unmute Audio
Audio is on by default.
1. Press "Program" button once. 2. Press button "A" once.
3. Press button "4" multiple 4. Press Kwikset button once.
times if needed to reach
desired state.
Green Keypad Buttons:
Feature is enabled.
Red Keypad Buttons:
Feature is disabled.
Manual Door Handing
If needed, the door handing process can be initiated manually.
This is useful if the lock is being moved to a different door.
1. Remove battery pack.
MMMYYWWSSSSSSS
3. Press 4. The latch bolt will extend
"Program" and retract to learn the
button once orientation of the door.
MMMYYWWSSSSSSS
more.
The Status LED will indicate
success or failure.
Network Information
Removing the lock from the network
Follow your smart home system's instructions
to remove the lock from the network. When
prompted by the system, press button "A" on
the lock interior once.
Z-Wave® System Notes
This product is a security enabled Z-Wave Plus product and must
be used with a Security Enabled Z-Wave controller to be fully
utilized. Z-Wave is a "Wireless mesh network," and results may
vary based on building construction and communication path.
To assure interoperability, each Z-Wave product must pass a stringent
conformance test to assure that it meets the Z-Wave standard
for complete compliance with all other devices and controls. The
Z-Wave identity mark assures consumers, integrators, dealers and
manufacturers that their products will reliably perform with any
other Z-Wave device. And, regardless of the vendor, always powered
nodes may act as a repeater for Kwikset/Weiser/Baldwin products.
Z-Wave Configuration and Association Parameters are available
on the Home Connect 620 page at www.kwikset.com.
System Alerts
Alert
Battery
pack
MMMYYWWSSSSSSS
Keypad flashes red
Button "A"
three times with three
beeps*.
"Program"
button
Status
LED
Keypad flashes red 15
Turnpiece
times with 15 beeps*
shaft
Keypad flashes red
with fast beeping
sound for three to four
seconds.
Keypad flashes red
with continuous
beeping sound for two
seconds.
Keypad flashes red
one time for 5 seconds
and beeps.
Status LED
The Status LED blinks every 6 seconds to communicate whether
the door is locked or unlocked. This feature is on by default.
Status LED Colors
Blinking Green
Blinking Amber
Blinking Red
to clear the code
Turn Status LED On/Off
1. Press "Program" button once. 2. Press button "A" once.
3. Press button "1" multiple
times if needed to reach
desired state.
Green Keypad Buttons:
Feature is enabled.
Red Keypad Buttons:
Feature is disabled.
2. Press and HOLD "Program"
button while reinserting the
battery pack.
Release button shortly
after battery pack is
installed. The status LED
will flash red and green. Status
LED
Success: LED flashes green
Failure: LED remains solid
red for 5 seconds
If the Status LED indicates a failure,
see the online Programming
and Troubleshooting Guide
or call Technical Support.
SmartKey Re-Keying
MMMYYWWSSSSSSS
Re-key the lock to work with your existing key. See the supplied
SmartKey Re-key instructions for more information.
Note: If Auto-Lock is enabled, remove the battery pack before
re-keying your lock.
Reference Guide
Reason Solution
Incorrect code entered. Re-enter code.
No user code Program at least one
programmed. user code.
Programming timeout
after six seconds.
Attempt programming
procedure again.
Unsuccessful
programming.
Three incorrect codes Re-enter code after
entered within one 60 second keypad
minute. lockout.
Low battery. Replace batteries.
Manually re-lock door.
Door jammed while
If needed, reposition
attempting to lock.
strike.
Manually re-hand the
Failed handing.
lock.
Unlocked
MMMYYWWSSSSSSS
Locked
Status
LED
Low battery
4. Press Kwikset button once.
Factory Reset
A Factory Reset will delete all codes associated with the lock and the lock's network settings but will not
remove the lock from the panel. Please run the Exclusion process to properly remove this lock from the
network before performing a Factory Reset. Please use this procedure only when the network primary
controller is missing or otherwise inoperable.
1. Remove battery pack.
MMMYYWWSSSSSSS
3. Press "Program" button once
more. LED will cycle flashing
between red and green while
the reset process is being
performed.
4 / 4
Deleting a single user code
Note: All codes may be deleted at once if the mastercode
is enabled. For more information about the mastercode,
consult the Programming and Troubleshooting Guide.
If no button is pressed for six seconds, the system will time
out, and you will need to restart the procedure.
1. Press "Program" button once. 2. Press Kwikset button once.
3. Enter user code to be 4. Press Kwikset button once.
deleted.
5. Re-enter user code. 6. Press Kwikset button once.
If unsuccessful: Make sure to enter the same valid code in steps 3 and 5.
Test code: While the door is open, test the user code
to make sure it no longer unlocks the door.
Auto-Lock
Auto-lock automatically re-locks the door after unlocking. This
feature is set to 30 seconds and is turned off by default.
Turn Auto-Lock On/Off
1. Press "Program" button once. 2. Press button "A" once.
3. Press button "2" multiple 4. Press Kwikset button once.
times if needed to reach
desired state.
Green Keypad Buttons:
Feature is enabled.
Red Keypad Buttons:
Feature is disabled.
Change Auto-Lock Time Delay
1. Press "Program" 2. Press button "A"
button once. once.
4. Press numeric button once that
corresponds to desired time delay:
1 30 sec.
2 60 sec. (1 min.)
3 180 sec. (3 min.)
4 300 sec. (5 min.)
5 600 sec. (10 min.)
2. Press and HOLD "Program"
button while reinserting the
battery pack.
Keep holding the button for 30
MMMYYWWSSSSSSS seconds until the lock beeps
and the status LED flashes red.
4. After a few seconds, the lock will initiate the door
handing process, and the latch bolt will extend and
retract to learn the orientation of the door.
MMMYYWWSSSSSSS
NOTE: The lock will auto-hand again after the
first time the door is locked or unlocked using
the keypad or app. This is to confirm the door
orientation.
Important Safeguards
1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Protect your user codes and mastercode.
5. Dispose of used batteries according to local laws and
regulations.
CAUTION: Prevent unauthorized entry. Since anyone with access
to the back panel can change the user codes, you must restrict
access to the back panel and routinely check the user codes to
ensure they have not been altered without your knowledge. The
use of a mastercode can help protect your system's settings.
WARNING: This Manufacturer advises that no lock can provide
complete security by itself. This lock may be defeated by forcible
or technical means, or evaded by entry elsewhere on the property.
No lock can substitute for caution, awareness of your environment,
and common sense. Builder's hardware is available in multiple
performance grades to suit the application. In order to enhance
security and reduce risk, you should consult a qualified locksmith
or other security professional.
©2021 Spectrum Brands, Inc. All Rights Reserved. Lake Forest, CA 92610.
3. Press button
"3" once.
5. Press Kwikset
button once.
MMMYYWWSSSSSSS
Status
LED