Kwikset HomeConnect 620 Installation And User Manual page 3

6
Add the lock to your smart home system
Initiate the process to add the lock
A
to your system at your smart home
controller. Refer to your smart
home system instructions for more
information.
SmartStart Enabled Products
SmartStart enabled
QR code
products can be added
into a Z-Wave network
by scanning the Z-Wave
QR Code present on the
product with a controller
providing SmartStart
inclusion. No further
action is required and the
SmartStart product will
be added automatically
within 10 minutes of being
switched on in the
network vicinity.
7
Add user codes (250 max)
A
It is recommended that you add and
delete all user codes through your
smart home control system. If your
system does not allow this, codes may
be added directly to the lock as shown
here.
Programming Timeout
During programming, if no button is
pressed for five seconds, the system
will time out (indicated by three beeps
and a red flashing Kwikset button), and
you will need to restart the procedure.
D
Mastercode
For enhanced security, a
mastercode may be used when
adding/deleting user codes and
adjusting lock configuration
settings. For more information
about the mastercode,
download the Programming
and Troubleshooting Guide on
the Home Connect 620 page
at kwikset.com/support.
8
Test the lock and check door alignment
A
With the door open, insert the key to
extend the latch. Ensure that the latch
extends smoothly.
If your door does not lock and unlock smoothly, make sure you replaced your previous latch and strike with those supplied
in the box. If you still experience locking errors, complete the troubleshooting steps at http://bit.ly/HC620jam
or call Kwikset Support: 1-866-863-6584
Install the interior cover
9
Important Information about the interior cover
The window on
window
the interior cover
is unlocked by
default for easier
access to the
battery pack
and buttons.
Cover Installation
a
Install cover.
Note: You may
need to rotate
the turn piece
to align with the
turn
turn piece shaft.
piece
If prompted by your smart home
B
system to add the lock, press button
"A" on the lock interior one time.
The red LED will illuminate when
the lock enters Add Mode.
MMMYYWWSSSSSSS
MMMYYWWSSSSSSS
Button "A"
Make sure the door is open.
Press the "Program" button once.
MMMYYWWSSSSSSS
What lights and sounds does the lock produce?
GREEN with ONE BEEP
Programming was successful.
B
Turn the key 180° to retract the latch.
Ensure that the latch
retracts smoothly.
For additional security,
you may choose to lock
the window by installing
the security screw.
Ensure you are using the
correct screws. Using
incorrect screws will
damage the product.
b
Install screws.
(For Lock Bag)
Ensure you are using the correct
turn
screws. Using incorrect screws
will damage the product.
piece shaft
At this time, you may be prompted
C
by your smart home system to
enter the 5-digit PIN found on
the label of the interior assembly.
If not, proceed to step D.
5-digit PIN
Enter user code. A total of 250 user
B
codes may be programmed.
or
green
1x
C
Close the door. Insert and rotate
the key to lock the door. Ensure
that the door locks smoothly.
68611 (1x)
(For Lock Bag)
Battery Pack Access
If the window is
unlocked, slide
69316 (3x)
up the window
to access the
battery pack
and buttons.
3 / 4
If successful, re-name the lock
D
in your system (if applicable).
If unsuccessful, follow your
system's instructions to remove
the lock from the controller and
any other network, then press
button "A" on the lock one time.
Perform steps A-C again.
MMMYYWWSSSSSSS
If still unsuccessful, consult
the Programming and
Troubleshooting Guide on
the Home Connect 620 page
at kwikset.com/support.
C Press button once.
Ensure the user
code is not a
duplicate, is
between 4 and
8 digits, and the
first 4 digits are
not the same as
another code.
RED with THREE BEEPS
Programming was unsuccessful.
Ensure the user code is not a duplicate, is
between 4 and 8 digits, and the first 4 digits
are not the same as another code.
Ensure the lock has room for an additional
code. If all user code positions are filled,
delete a code to make room for the new code.
D
Turn the key 180° to retract the latch.
Ensure that the door
unlocks smoothly.
For Lock
Bag
68611
actual size
When the window
is locked, you will
need to remove
the entire interior
cover and screws to
access the battery
pack and buttons.
If the window
is locked,
remove the
interior cover
and screws
to access the
battery pack
and buttons.
red
3x
(3x)
(1x)
69316
actual size