Stanley FatMax V20 SFMCF900 Original Instructions Manual page 8

ENGLISH
Installing and Removing the Battery Pack from
@
the tool
Warning! Make certain the lock-off button is engaged
to prevent switch actuation before removing or
installing battery.
To install battery pack (Fig. C)
● Insert battery pack firmly into tool until an audible click is
heard as shown in figure C. Ensure battery pack is fully
seated and fully latched into position.
To remove battery pack (Fig. D)
● Depress the battery release button (5) as shown in
figure D and pull battery pack out of tool.
@
Belt hook (Optional extra) (Fig. E, F)
Warning! To reduce the risk of serious personal
injury, place the forward/reverse button in the lock-off
position or turn tool off and disconnect battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start-up
@
can cause injury.
Warning! To reduce the risk of serious personal
injury, ONLY use the tool's belt hook (9) to hang the
tool from a work belt. DO NOT use the belt hook (9)
for tethering or securing the tool to a person or object
during use. DO NOT suspend tool overhead or
@
suspend objects from the belt hook.
Warning! To reduce the risk of serious personal
injury, ensure the screw (10) holding the belt hook
is secure.
Note: When attaching or replacing the belt hook (9), use only
the screw (10) that is provided. Be sure to securely tighten
the screw.
The belt hook (9) can be be attached by sliding into the
slots (8) on either side of the tool using only the screw (10)
provided, to accommodate left- or right- handed users. If the
hook is not desired at all, it can be removed from the tool.
To move the belt hook, remove the screw (10) that holds the
belt hook (9) in place then reassemble on the opposite side.
Be sure to securely tighten the screw (10).
Note: Various trackwall hooks and storage configurations
are available.
Please visit our website www.stanleytools.eu/3 for
further information.
@
Install accessory (Fig. G)
Warning! Use only impact accessories. Nonimpact
accessories may break and cause a hazardous
condition. Inspect accessories prior to use to ensure
that it contains no cracks.
8
(Original instructions)
● To install an accessory (11), firmly push accessory onto
the 12.7 mm hog ring anvil (3) . The hog ring compresses
to allow the accessory to slide on. After the accessory is
installed, the hog ring applies pressure to help provide
accessory retention.
Remove Accessory
● To remove an accessory, grasp the accessory and firmly
pull it off the 12.7 mm hog ring anvil.
@
Use
Warning! Let the tool work at its own pace. Do
not overload.
Selecting the direction of rotation (Fig. H)
For tightening, use forward (clockwise) rotation. For loosening,
use reverse (counterclockwise) rotation.
● To select forward rotation, push the forward/reverse
slider (2) to the left.
● To select reverse rotation, push the forward/reverse slider
to the right.
● To lock the tool, set the forward/reverse slider into the
centre position.
LED work light
The LED work light (12) is activated automatically when
the trigger is depressed. The LED work light will illuminate
when the trigger is partially depressed, before the unit
begins running.
Maintenance
Your Stanley FatMax tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
@
regular cleaning.
Warning! Before performing any maintenance on
the tool, remove the battery from the tool. Unplug the
charger before cleaning it.
● Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
● Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
● Regularly open the chuck and tap it to remove any dust
from the interior.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.