Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Stanley FATMAX V20 SFMCD715
Summary of Contents for Stanley FATMAX V20 SFMCD715
- Page 1 SFMCD715...
- Page 2 English (original instructions)
-
Page 4: Intended Use
ENGLISH (Original instructions) Intended use Your STANLEY FATMAX SFMCD715 Hammerdrill/ Screwdriver has been designed for screwdriving applications and for drilling in wood, metal, plastics and soft masonry. This appliance is intended for professional and private, non- professional users. Safety instructions... - Page 5 (Original instructions) ENGLISH Do not use any adapter plugs with earthed (grounded) g. If devices are provided for the connection of dust power tools. Unmodified plugs and matching outlets will extraction and collection facilities, ensure these are connected and properly used. Use of dust collection reduce risk of electric shock.
-
Page 6: Safety Instructions For All Operations
ENGLISH (Original instructions) likely to bend if allowed to rotate freely without contacting b. Use power tools only with specifically designated battery packs. Use of any other battery packs may create the workpiece, resulting in personal injury. b) Always start drilling at low speed and with the bit a risk of injury and fire. - Page 7 "Protecting the environment". Warning! Let the tool work at its own pace. Do not overload. Chargers Use your STANLEY FATMAX charger only to charge Charging the battery (Fig. A) the battery in the tool with which it was supplied. Other The battery needs to be charged before first use and batteries could burst, causing personal injury and damage.
- Page 8 ENGLISH (Original instructions) Battery state of charge indicator (Fig. B) Note: The charger will not charge a battery if the cell temperature is below approximately 10 °C or above 40 °C. The battery includes a state of charge indicator to quickly The battery should be left in the charger and the determine the extent of battery life as shown in figure B.
- Page 9 (Original instructions) ENGLISH Please visit our website www.stanley.eu/3 for Repeat until you reach the correct setting. further information. Use this setting for the remaining screws. Keyless chuck (Fig. G) Dual range switch (Fig J) Warning! Make certain the battery pack is removed to prevent The dual range feature of your drill allows you to shift gears tool actuation before installing or removing accessories.
-
Page 10: Troubleshooting
Maintenance Holes in wood can be made with the same twist drill bits used Your STANLEY FATMAX tool has been designed to operate for metal or with spade bits. These bits should be sharp and over a long period of time with a minimum of maintenance. -
Page 11: Ec Declaration Of Conformity
Steel/wood masonry These products also comply with Directive 2006/42/EC, 2014/30/EU and 2011/65/EU. For more information, please 1.2 (without battery) Weight contact STANLEY Europe at the following address or refer to the back of the manual. Charger SFMCB11 SFMCB12 SFMCB14 Input Voltage... - Page 12 United Kingdom STANLEY FATMAX Tel. 01753 511234 270 Bath Road Fax 01753 572112 Slough, Berkshire SL1 4DX www.stanleytools.co.uk N715599 REV-1 10/2019...
Need help?
Do you have a question about the FATMAX V20 SFMCD715 and is the answer not in the manual?
Questions and answers
I had to open my drill and need help to re assemble the gears
The Stanley V20 SFMCD715 drill does not provide instructions for reassembling gears. However, it explains how to shift between gears:
1. Make sure the tool is turned off and has come to a complete stop.
2. To select low speed, high torque (position 1), slide the gear shifter button away from the chuck.
3. To select high speed, low torque (position 2), slide the gear shifter button back toward the chuck.
4. Do not change gears while the tool is running.
Reassembling internal gears is not covered.
This answer is automatically generated