Advertisement
Quick Links
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
A.
Top
1 pc.
H.
Back Rail
1 pc.
I.
Back Rail
1 pc.
M.
N.
Rack Side
Rack Side
1 pc.
1 pc.
U.
V.
Leaf
Leaf
Support
Support
1 pc.
1 pc.
Hardware List
Hex Wrench
1 pc.
Caster
2 Locking
Small
2 Non-Locking
Hex Wrench
4 pcs.
1 pc.
Tool(s) required for assembly: Phillips screwdriver
home
451 -95
6
Kitchen Cart
B.
Side Panel
1 pc.
J.
Front Rail
1
pc
.
O.
P.
Rack Base
Rack Bar
1 pc.
1 pc.
X.
Front Rail
Door
1 pc.
1 pc.
M6x38
Magnet
Head Cap Bolt (long)
2 pcs.
4 pcs. (+1 extra)
M3x16
Wood Screw
M6x25
Head Cap Bolt
for Magnet
4 pcs. (+1 extra)
4 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,
servicedesk@homestylesfurniture.com,
C.
D.
Side Panel
Middle Panel
1 pc.
1 pc.
W.
Base
1 pc.
R.
S.
Door
1 pc.
M3x16
Wood Screw (short)
2 pcs. (+1 extra)
0
M6x12
Head Cap Bolt
for Caster
16 pcs. (+1 extra)
F.
Back Panel
3 pcs.
E.
Middle Panel
1 pc.
K.
Arm
2 pcs.
T.
Drawer
2 pcs.
Refer to later page(s) of these
instructions for drawer assembly.
M3x25
M3x25
Wood Screw (long)
Flat Head Screw
24 pcs. (+1 extra)
3 pcs. (+1 extra)
M3x16
Wood Screw
for Leaf Support
Adjustable Pin
16 pcs. (+1 extra)
6 pcs. (+1 extra)
888-680-7460
G.
Back Upright
2 pcs.
L.
Towel Bar
1 pc.
Q.
Shelf
4 pcs.
Handle
4 pcs.
M4x22
Machine Screw
8 pcs.
Advertisement
Related Manuals for Homestyles 451 -95
Summary of Contents for Homestyles 451 -95
- Page 1 451 -95 Kitchen Cart IMPORTANT Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed.
- Page 2 Assembly Instructions 2/8 IMPORTANT Ÿ Use a soft cloth between these parts and the floor. Ÿ Do not use power tools above 8 volts to assemble. Ÿ Do not tighten all the bolts until each part is properly assembled. Ÿ Keep Hex Wrench as the bolts may need to be tightened in the future.
- Page 3 Assembly Instructions 3/8 STEP 4 Attach Back Rail ( ) H to Side Panel (C), then flip Locks. (See Figures 1 and 2) Attach Back Uprights ( ) G to unit. Slide Back Panels ( ) F into position. Attach Back Rail ( ) I to unit, then flip Lock.
- Page 4 Assembly Instructions 4/8 STEP 6 Head Cap Bolt for Caster Non-Locking Caster Attach Casters to unit with Head Cap Bolts Locking Caster for Caster into pre-drilled holes with Locking Casters at front. (See Figure 4) Note: Arrow label indicates front of unit. Arrow label at front Figure 4 STEP 7...
- Page 5 Assembly Instructions 5/8 Wood Screw for Leaf Support STEP 8 Attach Leaf Supports (U) and (V) to unit with Wood Screws for Leaf Support. (See Figure ) 5 Figure 5 Wood Screw for Magnet Magnet STEP 9 Attach Magnets to Front Rail ( ) X by inserting Wood Screws for Magnet into pre-drilled holes, then tighten.
- Page 6 Assembly Instructions 6/8 Adjustable Pin Handle Machine Screw STEP 10 Attach Front Rail (X) to unit, then flip Locks. Insert Adjustable Pins into side panels and middle panels at desired level. (See Figure 7) Place Shelves (Q) into position. Attach Doors (R) and (S) by sliding door hinges into side panel hinges. (See Figure 8) Attach Handles to Doors (R) and (S) with Machine Screws.
- Page 7 Assembly Instructions / 7 8 Drawer (T) Bottom Wood Screw (long) STEP 11 Attach Drawer Front (T1) and Drawer Back (T2) to Drawer Side (T3) with Wood Screws (long). Attach Drawer Side (T4) to unit with Wood Screws (long). Roller at back Wood Screw (short) STEP 12 Slide Drawer Bottom (T5) into groove.
- Page 8 Assembly Instructions 8/8 Lock Flat Head Screw STEP 14 Attach Top (A) to unit with Flat Head Screws, then flip Locks. Slide Drawers (T) into position.
- Page 9 CARE INSTRUCTIONS NEVER NEVER use glass cleaners on allow liquids to remain on furniture. finished furniture. Ammonia Absorption causes parts to warp chemically attacks the finish. and split and finishes to delaminate. Do not use power tools Do not place Do not write above 8 volts to assemble.
Need help?
Do you have a question about the 451 -95 and is the answer not in the manual?
Questions and answers