Page 7
- Foreword Foreword You have just purchased a HAULOTTE® product and we would like to thank you for your business. The aerial work platform is a device for lifting people designed and manufactured with the intent to enable users to access overhead elevated temporary workplaces with the necessary tools and equipment.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Foreword 1 - User responsibility 1.1 - OWNER'S RESPONSIBILITY The owner (or hirer) has the obligation to : • To inform operators of the instructions contained in the Operator's Manual.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Foreword 1.4 - OPERATOR'S RESPONSIBILITY The operator has the obligation to : • Read and understand the contents of this manual and familiarize himself with the decals affixed on the machine.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Foreword 2 - Safety 2.1 - SAFETY INSTRUCTIONS 2.1.1 - Misuse Hazards • Do not use the machine for other purposes than to lift people, their tools and equipment to the desired position.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Foreword 2.1.2 - Falling Hazards To enter or exit from the platform : • The machine must be completely stowed. • Face the machine to access the entry opening to the platform.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Foreword 2.1.3 - Overturning / Tip-over Hazards Before positioning and operating the machine : • Ensure that the surface is capable of supporting the machine weight including the rated capacity.
Page 13
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Foreword Using a machine on a slope Do not drive the machine on slopes with gradients exceeding the authorised transveral and lateral limits for the machine. Section B 4.1 - Technical specifications.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Foreword 2.1.4 - Electrocution Hazards The machine is not electrically insulated and does not provide protection from contact or proximity to electrically charged conductors. Always position the lift at a safe distance from electrically charged conductors to ensure that no part of the machine is within an unsafe area.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Foreword 2.1.5 - Explosion / Fire Hazards • Always wear protective clothing and eye wear when working with batteries and power sources/systems. N.B.-:-A CID IS NEUTRALIZED WITH SODIUM BICARBONATE AND WATER •...
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Foreword 2.1.6 - Crushing / Collision Hazards When in the platform : • Check the work area for overhead clearance, for any obstacles besides and below the platform when raising/lowering the platform and or before driving.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Foreword 2.1.7 - Uncontrolled movement Hazards Never use a damaged or malfunctioning machine. Always respect the following rules : • Maintain clearance from high voltage lines. • Maintain clearance from generators, radar, electromagnetic fields.
Each inquiry or request should include all relevant information; including contact name, telephone number, mailing address, email address, plus the machine model and serial number. The HAULOTTE® Product Safety department will evaluate each request/inquiry and will provide a written response.
5 - Compliance 5.1 - PRODUCT MODIFICATION It is strictly forbidden to modify a HAULOTTE® product. Any modification may violate Haulotte design parameters, local regulations and industry standards. All modifications must be submitted in writing (form) and approved by the manufacturer.
It is important and necessary to keep HAULOTTE Services® updated with current ownership of the machine. This way, HAULOTTE® will be able to provide the necessary support for the product. If you have sold or transferred this machine(s); it is your responsibility to notify HAULOTTE Services®.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization Familiarization 1 - General safety 1.1 - INTENDED USE Do not operate the product in the following situations : • On soft, unstable or cluttered ground. • With wind blowing faster than the permissible limit : •...
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization 1.2 - DECAL CONTENT Decals are provided to alert the user of hazards inherent with the Aerial Work Platforms. Decals provide the following information : • The level of severity.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization 1.3 - SYMBOLS AND COLORS Symbols and colors are used to alert the operator of safety precautions and/or to highlight important safety information. The following safety symbols are used throughout this manual to indicate specific hazards and the hazard severity level when operating or maintaining the Aerial Work Platform.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization 1.5 - SYMBOLS LEGEND AND DEFINITIONS Symbols are used throughout this manual to depict hazards, avoidance measures and indicate when information is required. Refer to the following table to familiarize yourself with these symbols.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization 3.2 - MAINTENANCE SUPPORT The maintenance support (on both sides of the machine) must be put in place before any maintenance operations. COMPACT 10DX - COMPACT 2668RT...
Page 29
Maintenance operation - The stand located under one of the scissor arms must be set up : • For COMPACT 10DX - COMPACT 2668RT : Lift scissor arms to a sufficient height (floor of the platform at around 2,6 m / 8 ft 6 in from the ground).
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization 3.4 - PLATFORM CONTROL BOX 3.4.1 - Layout General view-COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT 4001029830 E 04.19 USA / GB...
Page 33
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization Controls and indicators Marking Item Description Function On : Machine switched on HL30 Power ON indicator Off : Machine switched off Pulled out : Platform control box power supply energized.
Page 34
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization Push the selector downwards to extend the stabilizers : Stabilizer extended and LED on (continuously: stabilizer extended and set against the ground; rapid flashing: Rear left stabilizer extension/retraction stabilizer extended but not yet set;...
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization 4 - Performance Specifications 4.1 - TECHNICAL CHARACTERISTICS For USA : The design standard used for manufacturing the machine depends on its date of manufacture. This changes certain technical features : •...
Page 36
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization CE, AS, EAC, CSA and ANSI A92.20 standards Machine COMPACT 10DX COMPACT 2668RT Characteristics - Dimensions Imp. Imp. Maximum working height 10,28 m 33 ft 9 in...
Page 37
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization CE, AS, EAC, CSA and ANSI A92.20 standards Machine COMPACT 12DX COMPACT 3368RT Characteristics - Dimensions Imp. Imp. Maximum working height 12,05 m 39 ft 6 in...
Page 38
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization ANSI A92.6 standard Machine COMPACT 2668RT COMPACT 3368RT Characteristics - Dimensions Imp. Imp. Maximum working height 10,28 m 33 ft 9 in 12,05 m 39 ft 6 in...
Page 50
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization EAC standard : Compact DX 4001029830 E 04.19 USA / GB...
Page 51
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization EAC standard : Compact DX Marking Color Description Quantity Compact 10 DX Compact 12 DX Height of the floor and load 4000046560 4000046570 Maximum Pressure per Tire - Floor...
Page 52
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Familiarization Marking Color Description Quantity Compact 10 DX Compact 12 DX Do not travel down slopes in high 4000275680 speed No admittance to unauthorized 307P227560 persons Do not park in the work area...
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Pre-operation inspection Pre-operation inspection 1 - Recommendations The owner, the site manager, the supervisor and the operator are all responsible to ensure the machine is fit for the work it is to perform; i.e. that the machine is suitable to carry out the work in complete safety and in compliance with this Operator's Manual.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Pre-operation inspection 3 - Inspection and Functional test 3.1 - DAILY INSPECTION Each day before the beginning of a new work session and with each change of operator, the machine must be subjected to a visual inspection and a complete functional test.
Page 55
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Pre-operation inspection Page or associated Comments procedure Chassis assembly : Wheel, reducer, steering, wheel pivot Check state of tires/tyres and inflations Clean the pads slide Thermal engines Check engine fuel level (Top up the oil if necessary)
Page 56
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Pre-operation inspection Page or associated Comments procedure General Check for the presence, cleanliness and readability of the manufacturer's plates, security labels, user manual and maintenance manual Check the cleanliness and readability of the control...
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Pre-operation inspection 4 - Safety functional checks To protect the user and the machine, safety systems prevent the movement of the machine beyond its operating limits. These safety systems when activated immobilize the machine and prevent further movement.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Pre-operation inspection 4.2 - ACTIVATION OF CONTROLS The deadman foot pedal (enable switch) must be activated to allow any movement. The "Enable Switch" system depends on the machine configuration and will consist of one of the following : •...
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Pre-operation inspection 4.5 - OVERLOAD SENSING SYSTEM If the platform load exceeds the maximum allowed load, no movement is possible from the 2 control boxes. At ground and platform control boxes a buzzer sounds and an indicator light warns the operator.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Pre-operation inspection 4.7 - TRAVEL SPEED LIMITATION The machine has a selector of 3 driving speeds - low, medium and high. All driving speeds are enabled when the machine is not elevated.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions Operation instructions 1 - Operation 1.1 - INTRODUCTION Only trained and authorized personnel shall be permitted to operate this aerial work platform. Prior to operation : •...
Page 62
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions • The status of the switches is tested automatically when the machine is switched on, and checked at every starting. A switch will be active only after it has been detected to be in neutral position. The following switches are not controlled : •...
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions 1.3 - OPERATION FROM THE PLATFORM CONTROL BOX • The platform control box can only be used if : • The E-stop buttons on both ground and platform control boxes are not pressed in.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions 2 - Ground control box 2.1 - TO START AND STOP THE MACHINE • Ensure that the E-Stop buttons ( 46 ) and ( 15 ) at the ground and platform control boxes are pulled out.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions Pull T-handle for emergency lowering N.B.-:-P ULLING ON TO THE ANDLE IMMEDIATELY ACTIVATES THE EMERGENCY LOWERING OF THE PLATFORM ALWAYS keep personnel and obstructions clear of the aerial work platform that might block the lowering.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions 3 - Platform control box 3.1 - TO START AND STOP THE MACHINE To start the machine : At the ground control box : • The E-stop button on the ground control box must be in ON position (pulled out / activated).
Page 67
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions Outriggers controls Command Action Push the central stabilizer extension/retraction selector (250) downwards until the machine is stable ( LED lit). Stabilizer extension/ retraction Push the central stabilizer extension/retraction selector (250) upwards until the stabilizers are fully retracted ( LED off).
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions 4 - Rescue and emergency procedures 4.1 - IN CASE OF POWER LOSS In case of loss of the main power source, lower the basket (or platform) using the T-handle on the chassis.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions 5 - Transportation 5.1 - PUTTING IN TRANSPORT POSITION During loading, ensure that : • The loading ramp can support the machine weight. • The loading ramp is correctly attached to transport vehicle.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions 5.3 - UNLOADING Before unloading, check that the machine is in good condition. • Remove the tie downs. • Pull the E-Stop buttons ( 15 ) at ground control box and ( 46 ) on the platform control box.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions 5.5 - STORAGE The machine can be stored in a designated area when not in use. If it has been stored for longer than 3 months without use then a periodic inspection must be conducted.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions 5.6 - LOADING AND UNLOADING To avoid any risk of sliding during loading, ensure that : • The loading ramp can bear the load. • The loading ramp is correctly attached.
• The lifting equipment ie. slings, shackles, hooks, lifting beam etc. are in good condition and of sufficient capacity. • The personnel performing the lift are authorised to safely perform the lift operation. Procedure for the use of slings - Compact 10DX (Compact 2668RT) - Compact 12DX (Compact 3368RT) 4001029830 E 04.19...
Page 77
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions Procedure for the use of slings - Compact 10DX (Compact 2668RT) - Compact 12DX (Compact 3368RT) - Front view of the machine 4001029830 E 04.19 USA / GB...
Page 78
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions Procedure for the use of slings - Compact 10DX (Compact 2668RT) - Compact 12DX (Compact 3368RT) - Rear view of the machine Maximum load per sling and...
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions 6 - Cold Weather Recommendations In cold weather conditions, allow engine to run for at least 5 min to warm up ; before operating any function thereby preventing any damage to the hydraulic system.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Operation instructions 6.2 - HYDRAULIC OIL External environmental conditions can reduce performance of the machine if the hydraulic oil temperature does not reach its optimum range. It is recommended to use the hydraulic oil according to weather condition. Refer to the table below.
1 - Machine dimensions Stowed / Transport position : Configuration that takes the minimum floor space necessary for storage and / or delivery of the machine - Access position - COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT...
• Consistent wear of the ground contact surface greater than Tires and rims are critical components for the stability of the machine. For safety reasons : • Use only HAULOTTE® spare parts according to the technical characteristics of the machine. Refer to the spare parts catalog.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - General Specifications 4.2.1 - Procedure of replacement Loosen the wheel nuts on the wheel to be removed. Raise the machine using a jack or a hoist. Remove the wheel nuts.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - General Specifications 5 - Options 5.1 - FOLDING GUARDRAILS 5.1.1 - Description Folding guardrails system is designed to allow guardrails to be lowered to reduce the overall height of the machine.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - General Specifications 5.1.3 - Fold down operation • Extension deck must be fully retracted and in locked position. • The intermediate sliding entrance bar must be at its lowest position.
Page 87
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - General Specifications Unlock the handle ( A ). Remove pin ( G3 ) from the right hand extension guardrail. Lift the guardrail and slowly tip it inwards, onto the platform floor.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - General Specifications Remove the pin ( G7 ). Lift and tip left hand main railing inwards until it contacts the element ( 6 ). 5.1.4 - Raising guardrails to working position To raise the folded guardrails to the vertical working position : •...
HAULOTTE Services® technicians are specially trained to carry out extensive repairs, interventions or adjustments on the safety systems or elements of HAULOTTE® machines. They carry genuine HAULOTTE spare parts and tools as required, and also provide fully documented reports on all work completed.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Maintenance 2 - Maintenance Schedule This section provides the necessary information needed to place the machine in safe operation. In accordance with the regulations that are currently applicable, this machine is deisgned to have a 10 year life span in normal usage conditions.
Local standards and regulations may require more frequent inspections. HAULOTTE® requires Reinforced and Major Inspections to be carried out on the product to extend its service life. Inspections must be carried out by a competent company or person.
This evaluation must occur at a frequency of 5000 hours or every 5 years. This inspection is the responsibility of the owner, and it must be conducted by a HAULOTTE Services® technician or by a competent company or person.
SPARE PARTS AND TOOLS AS REQUIRED ALSO PROVIDES FULLY DOCUMENTED REPORTS ON ALL WORK COMPLETED HAULOTTE Services® will not take responsibility for any outcomes resulting from inferior services or repairs performed by other unauthorised personnel. HAULOTTE® reminds that NO modifications SHALL be carried out without the written permission of HAULOTTE®.
• When contacting our After Sales Service, ensure that you provide the machine model and serial number. • When ordering any consumables or spare parts, please use this manual and the HAULOTTE® Essential catalogue to receive your genuine HAULOTTE® spare parts, your only guarantee of parts interchangeability and correct machine operation.
• If damage is caused by modifications that do not comply with HAULOTTE® specifications. • If lubricants, hydraulic oils or fuels that do not comply with HAULOTTE® recommendations are used. • If the machine is incorrectly repaired or used by the customer.
Page 97
• Hydraulic and fuel circuit contamination : Every possible precaution is taken to ensure that fuel and hydraulic liquid delivered is clean. HAULOTTE® will not accept any claims concerning cleaning of the fuel circuit, filter, injection pump or any other equipment in direct contact with fuel or lubricants.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Other information 2 - Subsidiary contact information HAULOTTE FRANCE HAULOTTE INDIA PARC DES LUMIERES HAULOTTE ITALIA Unit No. 1205, 12th foor,Bhumiraj Costarica, 601 RUE NICEPHORE NIEPCE VIA LOMBARDIA 15 Plot No.
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Other information 2.1 - CALIFORNIA WARNING For the engine powered machines destined to the US market (Standards ANSI and CSA) CALIFORNIA Proposition 65 Warning Operating, servicing and maintaining a passenger vehicle or...
Page 100
COMPACT 10DX - COMPACT 2668RT - COMPACT 12DX - COMPACT 3368RT - Other information Notes 4001029830 E 04.19 USA / GB...