SOMFY Oximo 40 Solar io Manual
  1. Manuals
  2. Brands
  3. SOMFY Manuals
  4. Control Unit
  5. Oximo 40 Solar io
  6. Manual

SOMFY Oximo 40 Solar io Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Oximo 40 Solar
Instructions
EN
Manuale
IT
Manual
ES
Instrukcja
PL
Návod
CS
io

Advertisement

Table of Contents
loading

Related Manuals for SOMFY Oximo 40 Solar io

Summary of Contents for SOMFY Oximo 40 Solar io

  • Page 1 Oximo 40 Solar Instructions Manuale Manual Instrukcja Návod...

  • Page 3: Table Of Contents

    Oximo 40 Solar io TRANSLATED INSTRUCTIONS These instructions apply to all Oximo 40 Solar io drives, the different versions of which are available in the current catalogue. CONTENTS 1. Prior information 3. Operation and maintenance 1.1. Field of application 3.1. Up and Down buttons 1.2.

  • Page 4: Prior Information

    Any After-Sales Service operation on the drive requires intervention by a drive and home automation professional. If in doubt when installing the drive, or to obtain additional information, contact a Somfy adviser or visit the website www.somfy.com.
  • Page 5 (h) of 9 mm. • The end of the drive antenna wire must protrude at least 10 cm from the roller shutter housing and be 1 cm from all ≥1 cm metal surfaces. Copyright 2021 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved. ©...

  • Page 6: Wiring

    • To guarantee good radio reception, do not cut the external antenna. • The cables and connectors must be protected from the roller shutter movement. • Somfy recommends placing the connectors behind the end piece and securing the cables inside the roller shutter housing.

  • Page 7: Commissioning

    Setting the end limits in Setting the end limits Somfy. manual mode (2.3.4.b) in semi-automatic mode (2.3.4.c) Step 3: Automatic setting of end limits (2.3.4.a) Step 4: Programming the control point (2.3.5) OPERATION Copyright 2021 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved. ©...
  • Page 8 5) To confirm the end limits, press the my button until the motorised product moves up and down. The end limits are programmed. Copyright 2021 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved. ©...
  • Page 9 3) Press the Up or Down button to move the motorised product to the new desired position. 4) To confirm the new end limit, press the my button until the motorised product moves up and down. Copyright 2021 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved. ©...

  • Page 10: Tips And Advice For Installation

    The motorised product does not respond to Commission the motorised product (see The motorised product is not set. the wake-up com- 2.3.). mand. Copyright 2021 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved. ©...
  • Page 11 (If the application is in the upper or lower limit position, it will make a brief up and down movement). 6) Press the PROG button on the Somfy local control point for ≈ 7 s until the motorised product moves up and down twice: the PROG. 7 drive is reset to the original configuration.

  • Page 12: Operation And Maintenance

    The control point battery is low. Check the battery and replace it as required. If the motorised product still does not work, contact a drive and home automation professional. Copyright 2021 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved. ©...

  • Page 13: Technical Data

    -20°C to + 60°C Index protection rating IP44 For more information about the technical data relating to this drive, please contact a Somfy representative. Please separate storage cells and batteries from other types of waste and recycle them via your local collection facility.
  • Page 14 SOMFY ACTIVITÉS SA 50 avenue du Nouveau Monde 74300 Cluses - FRANCE www.somfy.com 5149934A 100% recycled paper...

Table of Contents