Installation Requirements; Tools And Parts; Location Requirements - Whirlpool WVU57UC6F Installation Instructions And Use & Care Manual

Table of Contents

Advertisement

Available languages

Available languages

Tools and Parts

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
Drill
1¹⁄
" (3.0 cm) drill bit
4
¹⁄
" (3.0 mm) drill bit for pilot holes
8
Pencil
Wire stripper or utility knife
Tape measure or ruler
Caulking gun and weatherproof caulking com"und
Flat-blade screwdriver
Phillips screwdriver
Saber or keyhole saw
Metal snips
Parts supplied
Remove parts from package. Check that all parts are included.
#8-18 x 1" (4.2 mm x 25 mm) flat-head screws (2)
#8-18 x
/
" (4.2 mm x 16 mm) truss-head screws (4)
5
8
Drywall anchors (2)
Mounting brackets (2)
/
" x
/
" (3.5 mm x 5 mm) T10-head screws (2)
9
13
64
64
T10 TORX
adapter (1)
®†
3
/
" x 10" (8.3 cm x 25.4 cm) rectangular air transition (1)
1
4
Regular air damper (1)
Parts needed
Wall or roof cap with damper to match vent system
3 - UL Listed wire connectors
Vent clamps/duct tape as required
For 7" (17.8 cm) round vented installations:
7" (17.8 cm) round metal vent system
For 3¹⁄
" x 10" (8.3 cm x 25.4 cm) rectangular vented
4
installations:
3¹⁄
" x 10" (8.3 cm x 25.4 cm) rectangular metal vent system
4
For non-vented (recirculation) installations:
Charcoal filter kit. For information on ordering, see the
"Accessories" section.
®
TORX is a registered trademark of Acument Intellectual Properties, LLC.

INSTALLATION REQUIREMENTS

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.
It is the installer's responsibility to comply with installation
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located inside the range hood on
the left wall.
Range hood location should be away from strong draft areas,
such as windows, doors, and strong heating vents.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance. Consult the
cooktop/range manufacturer installation instructions before
making any cutouts.
This range hood is recommended for use with cooktops with
a maximum total rating of 55,000 BTUs or less.
Grounded electrical outlet is required. See the "Electrical
Requirements" section.
All openings in ceiling and wall where range hood will be
installed must be sealed.
These range hoods are factory set for vented installations.
Models that are capable of being installed as non-vented
(recirculating) require charcoal filters. See the "Accessories"
section to order charcoal filter kit.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.
Product Dimensions
B
A
I I
H
A. 6
19
B. 2" (5 cm)
C. 8
25
D. 1" (2.54 cm)
E. 8
32
F. 19
G. 1
/
1
H. 36" (91.4 cm)
30" (76.2 cm)
I.
/
55
C
D
E
G
F
/
" (16 cm)
54
/
" (21.3 cm)
64
/
" (22.8 cm)
32
11
/
" (50 cm)
16
" (3.8 cm)
2
" (2.2 cm)
64
5

Advertisement

Table of Contents
loading

This manual is also suitable for:

Wvu57uc0fWvu57uc0fsWvu57uc6fs

Table of Contents