Related Manuals for Rhin-O-Tuff KF-50
Summary of Contents for Rhin-O-Tuff KF-50
- Page 1 Rhin-O-Tuff KF-50 Plastic Coil Crimper Instruction Manual Provided By http://www.MyBinding.com http://www.MyBindingBlog.com...
- Page 2 An in-depth look at the set up procedures necessary to achieve maximum results follows. See Figure A: The KF-50 Krimp-Fast Coil Crimper can attach to the right side of the HD-4170 Heavy Duty Coil Inserter Module (1) and the PC-248 Punch and Electric Coiling System (2).
- Page 3 PC-248 Punch & Electric Coil Insertion System The first fully featured Manual Punch and Electric Coil Inserter with Heavy Duty Features at an affordable price. Offers significant productivity gains through operator driven common sense solutions. KF-50-OTM Instruction Book KF-50 Issue 1 Page 2 KF-50 Patent Pending...
-
Page 4: Table Of Contents
Warranty Registration Card Information: Please fill this out immediately and mail in. Product registration is important to establish trouble free warranty repair of any of your Rhin-O-Tuff equipment. Please fill out and mail in the card provided with your machine or register on-line at www.RHIN-O-TUFF.com... -
Page 5: Important Safety Notice
Important Safety Notice! Make sure you read this section very carefully! Learn to recognize this Safety Alert Symbol. The KF-50 has been designed to provide a very high level of protection to an operator. Follow the guidelines below while installing, operating and maintaining your machine. -
Page 6: Out Of The Box" Initial Setup
(as shown), Replace the Coil Guide Clamp Screw (5) to secure the guides in place. Fine adjustment will be made later in this manual. Continue to Chapter 3. Fig. C KF-50-OTM Instruction Book KF-50 Issue 1 Page 5 KF-50 Patent Pending... -
Page 7: Kf-50 And Kf-50E41
Chapter 1 “Out of the Box” initial Setup Continued… 1.2) KF-50 and KF-50e41: See Figure D. The KF-50 and KF-50e41 came partially assembled to protect items from damage during shipment. Locate the following items supplied in the shipping kit. (1) Book End Stop... - Page 8 Fasten these three items together with the Coil Guide Clamp Screw (5) creating the Coil Guide Assembly. (This step may have already assembled by the factory) Fig. E KF-50-OTM Instruction Book KF-50 Issue 1 Page 7 KF-50 Patent Pending...
-
Page 9: The Kf-50Kb Is Pre-Installed, Please Go To Chapter 3
See Figure F. Place the Coil Guide Assembly’s Coil Guide Support onto the loosened screw as shown. Center the Coil Guide Assembly Coil Guides into the slot in the main body of the KF-50 Crimper and tighten screw. The KF-50 will look like the various views below. - Page 10 Feed it completely through the large hole on the right side of the KF-50 as it’s oriented and shown in Fig. J (2). Set the KF-50 along side the coiler so that the 3-3/4” screw, now protruding out of the left side of the KF-50, inserts into the available hole left over from the previous step in Fig.
-
Page 11: Kf-50E41 Mounted To A Hd-E4100
Continue past Fig. K to the next step for the left end screw. *** Prior to Serial Number 1E01040 the second mount hole was not added. Call Technical Support at 1-800-390-5782 for the HD-e4100/KF-50 Hole Kit. You will need an electric drill and small clamp or small Vice-Grip® when you receive the Kit. - Page 12 Feed it completely through the large hole on the right side of the KF-50 as it’s oriented and shown in Fig. M (2). Set the KF-50 along side the coiler so that the 3-3/4” screw, now protruding out of the left side of the KF-50, inserts into the available hole left over from the previous step in Fig.
-
Page 13: Operation
Refer back to this figure as needed. Fig. M Important Notice: ALWAYS keep the Crimp Anvil Lock TIGHTENED while crimping. Failure to do so will cause premature wear to these mechanisms. KF-50-OTM Instruction Book KF-50 Issue 1 Page 12 KF-50 Patent Pending... -
Page 14: Set Crimper To Coil Size
3.2.1) The first step to setting your crimper is by determining how long of tail (1) you need. There are two settings for the KF-50, 6-50MM and 15-50MM indicated by the label (2), the difference is a short tail or long tail. The 6-50MM setting creates a short tail for all sizes of coil. - Page 15 Anvil and Coil Clamp Wheel (2) as shown. Loosen the Book End Clamp (3) ¼ turn and adjust the Book End Stop against the book (4). Tighten Book End Clamp (3). Fig. R KF-50-OTM Instruction Book KF-50 Issue 1 Page 14 KF-50 Patent Pending...
-
Page 16: Crimp Knob Final Adjustments And Crimping
Coil Cut Wheel it will tear-up and noticeably damage the coil (2). If the Crimping Anvil is too far away from the Coil Cut Wheel, the crimp will un-do and become un-crimped within a day (3). Fig. T KF-50-OTM Instruction Book KF-50 Issue 1 Page 15 KF-50 Patent Pending...
Need help?
Do you have a question about the KF-50 and is the answer not in the manual?
Questions and answers