HIKVISION HF-VS409 User Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Digital Camera
  5. HF-VS409
  6. User manual
HIKVISION HF-VS409 User Manual

HIKVISION HF-VS409 User Manual

Smoke detection camera
Hide thumbs Also See for HF-VS409:
Table of Contents

Advertisement

Quick Links

HF-VS409 Smoke Detection Camera
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HF-VS409 and is the answer not in the manual?

Questions and answers

Related Manuals for HIKVISION HF-VS409

Summary of Contents for HIKVISION HF-VS409

  • Page 1 HF-VS409 Smoke Detection Camera User Manual...
  • Page 2 WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,...
  • Page 3 HF-VS409 Smoke Detected Camera User Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
  • Page 4 HF-VS409 Smoke Detected Camera User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazardous situation which, if not avoided, will or could Danger result in death or serious injury.

  • Page 5: Table Of Contents

    HF-VS409 Smoke Detected Camera User Manual Contents Chapter 1 Safety Instruction ....................... 1 Chapter 2 Regulatory Information ....................3 Chapter 3 Overview ........................5 3.1 Introduction ........................... 5 3.2 Features ..........................5 3.3 Appearance ..........................5 3.4 Indicator & Buzzer Status ....................... 9 Chapter 4 Installation .......................
  • Page 6 HF-VS409 Smoke Detected Camera User Manual 7.2 Playback ..........................22 7.3 Picture ..........................23 7.4 Parameter Settings ....................... 24 7.4.1 Local ..........................24 7.4.2 System ......................... 25 7.4.3 Network Settings ......................31 7.4.4 Video/Audio Settings ....................42 7.4.5 Image Settings ......................45 7.4.6 Event and Alarm Settings ....................

  • Page 7: Chapter 1 Safety Instruction

    HF-VS409 Smoke Detected Camera User Manual Chapter 1 Safety Instruction Warning All the electronic operation should be strictly compliance with the electrical safety regulations, ● fire prevention regulations and other related regulations in your local region. Do not connect several devices to one power adapter as adapter overload may cause over-heat ●...
  • Page 8 HF-VS409 Smoke Detected Camera User Manual CAUTION: Risk of explosion if the battery is replaced by an incorrect type. ● Improper replacement of the battery with an incorrect type may defeat a safeguard (for ● example, in the case of some lithium battery types).

  • Page 9: Chapter 2 Regulatory Information

    HF-VS409 Smoke Detected Camera User Manual Chapter 2 Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
  • Page 10 HF-VS409 Smoke Detected Camera User Manual under the EMC Directive 2014/30/EU, LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.

  • Page 11: Chapter 3 Overview

    Chapter 3 Overview 3.1 Introduction HF-VS409 series visual smoke detection camera integrates smoke detection, temperature detection and video perception as well as video intelligent analysis. The camera can detect heat and smoke in the early stage of a fire hazard, facilitate intelligent video analysis and provide warnings by sending out audible and visual alarm signals and showing alarm information and relevant images and video clips in the video surveillance system.
  • Page 12 HF-VS409 Smoke Detected Camera User Manual Dimensions Figure 3-1 Dimensions...
  • Page 13 HF-VS409 Smoke Detected Camera User Manual Appearance and Interface Figure 3-2 Appearance...
  • Page 14 HF-VS409 Smoke Detected Camera User Manual Figure 3-3 Interface MicroSD Card Slot Insert microSD card for local storage. RESET Button Hold the RESET button and power on the device. Hold the button for 10 to 15 seconds while the device is powered on. Release the button and the device will be restored to default settings.

  • Page 15: Indicator & Buzzer Status

    HF-VS409 Smoke Detected Camera User Manual Indicator Refer to Indicator & Buzzer Status for details. TAMPER If the device is pulled off its base by force, the button will pop out to trigger the tampering alarm. Power Interface 12 VDC power supply Note Make sure the power supply connect correctly.
  • Page 16 HF-VS409 Smoke Detected Camera User Manual Indicator Buzzer Status Flashing red every 40 seconds Beeping every 40 seconds Low voltage Quick flashing green 3 times Disable Tampering alarm Flashing yellow every 40 Beeping every 40 seconds Maze pollution seconds Flashing red every 100 seconds Disable...

  • Page 17: Chapter 4 Installation

    HF-VS409 Smoke Detected Camera User Manual Chapter 4 Installation 4.1 Installation Description Install the alarm according to the instructions in this manual. ● To prevent injury, please ensure the alarm is securely attached to the wall or the ceiling. ●...

  • Page 18: Ceiling Mounting Without Junction Box

    HF-VS409 Smoke Detected Camera User Manual 4.3 Ceiling Mounting without Junction Box Steps 1. Drill 4 screw holes on the ceiling according to the mounting template. 2. Insert the plastic expansion sleeves into the screw holes, and fix the mounting base with screws.
  • Page 19 HF-VS409 Smoke Detected Camera User Manual 3. Fix the mounting base to the junction box with screws. 4. Smooth the cables and turn the smoke detector clockwise until it snaps in place. Figure 4-3 Installation Illustration...

  • Page 20: Chapter 5 Quick Operation

    Get the SADP software from the supplied disk or the official website http:// ● www.hikvision.com/ , and install the SADP according to the prompts. The device and the PC that runs the SADP tool should belong to the same subnet.

  • Page 21: Activate Device Via Web Browser

    HF-VS409 Smoke Detected Camera User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP.

  • Page 22: Access Device Via Web Browser

    HF-VS409 Smoke Detected Camera User Manual we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product. 4. Click OK to complete activation and enter Live View page.

  • Page 23: Chapter 6 Local Settings

    HF-VS409 Smoke Detected Camera User Manual Chapter 6 Local Settings 6.1 Smoke/Temperature Alarm In standby mode, when smoke particles or the temperature reach the settings, the alarm will be triggered. The buzzer will beep and the indicator keeps red. Note You can enable the function via web to upload the alarm records, smoke concentration and pollution data to platforms and FTP.

  • Page 24: Chapter 7 Remote Configuration Via Web

    HF-VS409 Smoke Detected Camera User Manual Chapter 7 Remote Configuration via Web 7.1 Live View The live view page allows you to view the real-time video, capture images, realize PTZ control, set/ call presets and configure video parameters. Log in the device to enter the live view page, or click Live View on the menu bar of the main page to enter the live view page.
  • Page 25 HF-VS409 Smoke Detected Camera User Manual Figure 7-2 Live View Page (General Settings) Manu Bar Click the tab to enter Live View, Playback, Picture and Configuration page respectively. Live View Window Display the live video on the display window of live view.
  • Page 26 HF-VS409 Smoke Detected Camera User Manual Figure 7-3 Live View Page Table 7-1 Descriptions of Live Icons Icon Description Start all live view. Stop all live view. Clear Capture images. Manually start/stop recording. Start/Stop digital zoom. Mute Audio on and adjust the volume.
  • Page 27 HF-VS409 Smoke Detected Camera User Manual Icon Description Webcomponents MJPEG Digital Zoom: 1. Click to start the function. 2. Click the mouse on the live view image and drag it to a lower right position. The area in the red rectangle will be zoomed in after you release the mouse.

  • Page 28: Playback

    HF-VS409 Smoke Detected Camera User Manual Table 7-2 Descriptions of PTZ Control Panel Icon Description Direction buttons Start/Stop auto scan Zoom in/Zoom out Focus -/Focus + Iris -/Iris + Adjust speed of pan/​ ti lt movements Enable/disable light Auxiliary focus...

  • Page 29: Picture

    HF-VS409 Smoke Detected Camera User Manual 1) Drag the timeline to a specific time and click to play the recording. 2) If you need to play the recordings on a specific time, set Time at Locate Play Time and click .

  • Page 30: Parameter Settings

    HF-VS409 Smoke Detected Camera User Manual 7.4 Parameter Settings 7.4.1 Local Click Configuration → Local to enter the settings page. Video Parameters Protocol configure settings according to actual practice. Play Performance configure settings according to actual practice. Rule Information You can click to Enable or Disable the rule information. If the function is enabled, the preview interface will display info boxes, such as dynamic analysis of motion detection.

  • Page 31: System

    HF-VS409 Smoke Detected Camera User Manual Click Browse to change path. Click Open to open the folders that save the clips. 7.4.2 System System Settings Note system settings may vary according to different device models and the followings are possible system settings supported by the device.
  • Page 32 HF-VS409 Smoke Detected Camera User Manual Click Configuration → System → System Settings → About and click View to view open source software licenses. Maintenance Upgrade and Maintenance Click Configuration → System → Maintenance → Upgrade and Maintenance to reboot device, set parameters, import/export and upgrade.
  • Page 33 HF-VS409 Smoke Detected Camera User Manual Upgrade Files If the device needs upgrading, you can copy the upgrade program to your PC, clickBrowse to choose the save path, and click Upgrade. Note The upgrading process will be 1 to 10 minutes, please do not power off. The device will restart automatically after upgrading.
  • Page 34 HF-VS409 Smoke Detected Camera User Manual Note If mutual-authentification is required for the server, the device needs to install both client certificate and CA certificate. If not, the device needs to install CA certificate. 1. Click Configuration → System → Maintenance → Security Audit Log .
  • Page 35 HF-VS409 Smoke Detected Camera User Manual Note Requirement for basic authentication is rather simple. To ensure high-level cyber security, the digest authentication is recommended. IP Address Filter Set permissions for visits from computers or other terminals. Note IP address refers to IPv4 address.
  • Page 36 HF-VS409 Smoke Detected Camera User Manual Click Account Security Settings and input password for the admin user account to set or change security questions. After configuration, click Forget Password on the login page and answer the security questions to reset your password.

  • Page 37: Network Settings

    HF-VS409 Smoke Detected Camera User Manual 7.4.3 Network Settings TCP/IP TCP/IP settings must be properly configured before you operate the device over network. IPv4 and IPv6 are both supported. Both versions can be configured simultaneously without conflicting to each other.
  • Page 38 HF-VS409 Smoke Detected Camera User Manual Input IPv6 Address, IPv6 Subnet, IPv6 Default Gateway. Consult the network administrator for required information. It stands for maximum transmission unit. It is the size of the largest protocol data unit that can be communicated in a single network layer transaction.
  • Page 39 HF-VS409 Smoke Detected Camera User Manual Set PPPoE This device supports the PPPoE auto dial-up function. The device gets a public IP address by ADSL dial-up after the device is connected to a modem. You need to configure the PPPoE parameters of the device.
  • Page 40 HF-VS409 Smoke Detected Camera User Manual It refers to the port through which the browser accesses the device. For example, when the HTTP Port is modified to 81, you need to enter http://192.168.1.64:81 in the browser for login. RTSP Port It refers to the port of real-time streaming protocol.
  • Page 41 HF-VS409 Smoke Detected Camera User Manual Set Auto Port Mapping Steps 1. Check Enable UPnP™, and choose a friendly name for the camera, or you can use the default name. 2. Select the port mapping mode to Auto. 3. Click Save.
  • Page 42 HF-VS409 Smoke Detected Camera User Manual 4. Click Save. Set FTP Set FTP parameters if you want to upload the captured pictures to the FTP server. Before You Start Set the FTP server, and ensure the device can communicate normally with the server.
  • Page 43 - Visit https://appstore.hikvision.com to download the application according to your mobile phone system. - Visit the official site of our company. Then go to Support → Tools → Hikvision App Store . - Scan the QR code below to download the application.
  • Page 44 If errors like "Unknown app" occur during the installation, solve the problem in two ways. Visit https://appstore.hikvision.com/static/help/index.html to refer to the troubleshooting. ● Visit https://appstore.hikvision.com/ , and click Installation Help at the upper right corner of ● the interface to refer to the troubleshooting.
  • Page 45 HF-VS409 Smoke Detected Camera User Manual Set ISUP When the device is registered on ISUP platform (formerly called Ehome), you can visit and manage the device, transmit data, and forward alarm information over public network. Steps 1. Go to Configuration → Network → Advanced Settings → Access Platform .
  • Page 46 HF-VS409 Smoke Detected Camera User Manual Note Network can identify the priority of data transmission. The bigger the DSCP value is, the higher the priority is. You need to set the same value in router while configuration. 3. Click Save.
  • Page 47 HF-VS409 Smoke Detected Camera User Manual Steps Note This function varies according to different models. 1. Go to Configuration → Network → Advanced Settings → Network Service . 2. Set network service. WebSocket & WebSockets WebSocket or WebSockets protocol should be enabled if you use Google Chrome 57 and its above version or Mozilla Firefox 52 and its above version to visit the device.

  • Page 48: Video/Audio Settings

    HF-VS409 Smoke Detected Camera User Manual Steps 1. Go to Configuration → Network → Advanced Settings → Alarm Server . 2. Enter Destination IP or Host Name, URL, and Port. 3. Optional: Check Enable to enable ANR. 4. Select Protocol.
  • Page 49 HF-VS409 Smoke Detected Camera User Manual Set the max. bitrate from 32 to 16384 Kbps. The higher value corresponds to the higher video quality, but the better bandwidth is required. Video Encoding The device supports H.264 and H.265. Smart264 and Smart265 Smart264 If you set the main stream as the stream type, and H.264 as the video encoding, you can see...
  • Page 50 HF-VS409 Smoke Detected Camera User Manual The audio settings includes the audio encoding, audio input, input volume and the environment noise filter. Audio Encoding G.722.1, G.711 ulaw, G.711alaw, G.726, MP2L2 and PCM are selectable. For MP2L2, the Sampling Rate and Audio Stream Bitrate are configurable. For PCM, the Sampling Rate can be set.

  • Page 51: Image Settings

    HF-VS409 Smoke Detected Camera User Manual 7. Optional: Select other region No. and repeat the above steps if you need to draw multiple fixed regions. Display Info. on Stream The information of the objects (e.g. human, vehicle, etc.) is marked in the video stream. You can set rules on the connected rear-end device or client software to detect the events including line crossing, intrusion, etc.
  • Page 52 HF-VS409 Smoke Detected Camera User Manual Note Day/Night Switch function varies according to models. Supplement Light Smart Supplement Light This feature uses smart image processing technology to reduce overexposure caused by supplement light. IR Light Mode When the mode is set to Auto, the supplement light is automatically turned in or off according to the image brightness.
  • Page 53 HF-VS409 Smoke Detected Camera User Manual DNR reduces the noise in the video stream. OFF, Normal Mode and Expert Mode are selectable. Under normal mode, set the DNR level from 0 to 100, and the default value is 50. Under expert mode, you can set Space DNR Level and Time DNR Level separately.

  • Page 54: Event And Alarm Settings

    HF-VS409 Smoke Detected Camera User Manual 3) Click Stop Drawing to finish drawing. 4. Optional: Click Clear All to clear all the configured privacy masks. 5. Click Save. Image Parameters Switch The device automatically switches image parameters in set time periods.
  • Page 55 HF-VS409 Smoke Detected Camera User Manual Send Email Check Send Email, and the device sends an email to the designated addresses with alarm information when an alarm event is detected. For email settings, refers to Set Email . Notify Surveillance Center Check Notify Surveillance Center, the alarm information is uploaded to the surveillance center when an alarm event is detected.
  • Page 56 HF-VS409 Smoke Detected Camera User Manual 7. Click Save. Set Video Tampering Alarm When the configured area is covered and cannot be monitored normally, the alarm is triggered and the device takes certain alarm response actions. Steps 1. Go to Configuration → Event → Basic Event → Video Tampering .
  • Page 57 HF-VS409 Smoke Detected Camera User Manual 6. Click Save. Set Alarm Input Alarm signal from the external device triggers the corresponding actions of the current device. Before You Start Make sure the external alarm device is connected. See Quick Start Guide for cable connection.
  • Page 58 HF-VS409 Smoke Detected Camera User Manual Custom a name for the alarm output. Delay It refers to the time duration that the alarm output remains after an alarm occurs. 2. Set the alarming schedule. For the information about the settings, see Set Arming Schedule .
  • Page 59 HF-VS409 Smoke Detected Camera User Manual Set Smoke Detection Smoke detection function detects the concentration of the smoke. When the concentration of the smoke is over the limit, the alarm will be triggered. Steps 1. Click Configuration → Event → Normal Event → Smoke Detection .
  • Page 60 HF-VS409 Smoke Detected Camera User Manual Smart Event Set Intrusion Detection Intrusion detection function detects people, vehicle or other objects which enter and loiter in a pre-defined virtual region, and some certain actions can be taken when the alarm is triggered.
  • Page 61 HF-VS409 Smoke Detected Camera User Manual 3) Click on the line, and drag its end points to adjust the length and position. 4) Select the Direction for the detection line. Direction It stands for the direction from which the object goes across the line.
  • Page 62 HF-VS409 Smoke Detected Camera User Manual Detection You can specify the object type, and the device only detects the selected Target type of objects. 8. Click Save. 9. Repeat above steps to set other lines. 10. Set arming schedule. See Set Arming Schedule .
  • Page 63 HF-VS409 Smoke Detected Camera User Manual Fire Source Detection The function is developed to detect the fire source in the detection area. If fire sources are spotted and the duration reaches the setting, the fire alarm will be triggered and a series of operations will be executed.

  • Page 64: Storage Settings

    HF-VS409 Smoke Detected Camera User Manual Before You Start Note Indoor Passage Blockage Detection and Fire Source Detection will be out of service when On/Off Duty Detection is enabled. Steps 1. Click Configuration → Event → Smart Event → On/Off Work Detection .
  • Page 65 HF-VS409 Smoke Detected Camera User Manual Set New or Unencrypted Memory Card Before You Start Insert a new or unencrypted memory card to the device. For detailed installation, refer to Quick Start Guide of the device. Steps 1. Click Configuration → Storage → Storage Management → HDD Management .
  • Page 66 The device detects the status of Hikvision memory card. You receive notifications when your memory card is detected abnormal. Before You Start The configuration page only appears when a Hikvision memory card is installed to the device. Steps 1. Click Configuration → Storage → Storage Management → Memory Card Detection .
  • Page 67 HF-VS409 Smoke Detected Camera User Manual If you use the memory card on the device that locks it, unlocking will be done automatically ● and no unlocking procedures are required on the part of users. If you use the memory card (with a lock) on a different device, you can go to HDD ●...
  • Page 68 HF-VS409 Smoke Detected Camera User Manual Set Cloud Storage It helps to upload the captured pictures and data to the cloud. The platform requests picture directly from the cloud for picture and analysis. The function is only supported by certain models.
  • Page 69 HF-VS409 Smoke Detected Camera User Manual Note The record type is vary according to different models. Continuous The video will be recorded continuously according to the schedule. Motion When motion detection is enabled and trigger recording is selected as linkage method, object movement is recorded.

  • Page 70: The Third-Party Platform

    HF-VS409 Smoke Detected Camera User Manual The recordings are deleted when they exceed the expired time. The expired time is configurable. Note that once the recordings are deleted, they can not be recovered. 6. Click Save. Capture Automatically This function can capture pictures automatically during configured time periods.
  • Page 71 UD24996B...

Table of Contents

Save PDF