Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HIKVISION Wiegand iDS-2CD7A26G0/P-IZHSY
Summary of Contents for HIKVISION Wiegand iDS-2CD7A26G0/P-IZHSY
- Page 1 Wiegand Camera Operation Manual...
-
Page 2: Table Of Contents
Wiegand Camera ·Operation Manual Contents 1 Introduction ....................1 2 Cameras ....................... 2 2.1 Available Models ........................2 2.2 Wiegand Interface Appearance ....................2 3 Transfer Plate Number via Wiegand Protocol ..........3 3.1 Card ID 26-bit ........................... 3 3.1.1 Protocol Standard ......................3 3.1.2 Configuration ........................ -
Page 3: Introduction
Wiegand Camera ·Operation Manual 1 Introduction This manual is about the Wiegand configuration and features of network cameras. The manual is created as a guide for the technical support engineer, sales engineer, etc. Currently overseas license plate cameras support 4 Wiegand protocols: Card ID 26-bit Wiegand protocol, Hik 34-bit Wiegand protocol, NEWG 72bit Wiegand protocol and SHA-1 26-bit Wiegand protocol. -
Page 4: Cameras
Wiegand Camera ·Operation Manual 2 Cameras 2.1 Available Models The available models of network cameras are: iDS-2CD7A26G0/P-IZHSY (2.8-12 mm)(C) iDS-2CD7A26G0/P-IZHSY (8 to 32 mm)(C) iDS-2CD7A46G0/P-IZHSY (2.8-12 mm)(C) iDS-2CD7A46G0/P-IZHSY (8 to 32 mm)(C) 2.2 Wiegand Interface Appearance Figure 2-1 Wiegand Interface Connection: Connect the block’s D0, D1 and GND to those of receiving terminal accordingly. -
Page 5: Transfer Plate Number Via Wiegand Protocol
Wiegand Camera ·Operation Manual 3 Transfer Plate Number via Wiegand Protocol 3.1 Card ID 26-bit 3.1.1 Protocol Standard Map the license plate number with the access control card number. Find the related card number in allowlist and blocklist, and transfer the card information (26 bit) via Wiegand interface. -
Page 6: Configuration
Wiegand Camera ·Operation Manual 9 10 25 26 …… …… Parity Bit Data Bits Parity Bit Figure 3-2 Wiegand Format Bit 1 is an even parity bit for the first 12 bits (bit 2 to bit 13). Bit 26 is an odd parity bit for the last 12 bits (bit 14 to bit 25). ... - Page 7 Wiegand Camera ·Operation Manual Figure 3-3 Wiegand Configuration Interface Vehicle Detection Configuration Steps: Go to VCA->Road Traffic->Detection Configuration. Check the checkbox of Enable to enable Vehicle Detection. Set the specific detection parameters, which are the same as those of conventional ANPR cameras. Figure 3-4 Detection Configuration Interface...
-
Page 8: Hik 34Bit
(34 bit) via Wiegand interface. Determine whether the car has permission to pass according to the card number. The protocol for directly transferring the access control card No. through the Wiegand interface is a private protocol of Hikvision, compatible with Hikvision access control system. -
Page 9: Configuration
The return result (even parity bit + card data +odd parity bit) will be sent to Hikvision access control device supporting Wiegand protocol. The front parity bit is the even parity bit of the first 16 bits of the card number. -
Page 10: Sha-1 26Bit
Wiegand Camera ·Operation Manual Go to Configuration-> System Settings->Wiegand to enable wiegand transfer and select protocol type. Figure 3-6 Wiegand Configuration Interface For the steps to enable Vehicle Detection and Blocklist &Allowlist Configuration, please see 3.1.2 Configuration. Note: When importing the plates’ list. The Card No. -
Page 11: Configuration
Wiegand Camera ·Operation Manual Figure 3-7 Wiegand Protocol Flow Chart Example: Here we take the license plate number HK55EVB as example. The coding steps are shown as follows. Steps: Convert HK55EVB by SHA1 mode is: 0x80cf15. Output a 8-bit binary code for each set of number via the Wiegand interface: 1000 0000 1100 1111 0001 0101... -
Page 12: Newg 72Bit
Wiegand Camera ·Operation Manual Figure 3-8 Wiegand Configuration Interface For the steps to enable Vehicle Detection, please see 3.1.2 Configuration. Blocklist &Allowlist Configuration is not required. 3.4 NEWG 72bit 3.4.1 Protocol Standard The 72-bit Wiegand format contains 72 data bits and no parity bit. 72 data bits represents for the license plate number information. -
Page 13: Configuration
Wiegand Camera ·Operation Manual Note: NEWG 72bit Wiegand protocol does not support transfer license plate number with non-English characters. 3.4.2 Configuration Set Wiegand Type as NEWG 72bit Steps: Go to Configuration-> System Settings->Wiegand to enable wiegand transfer and select protocol type. Figure 3-9 Wiegand Configuration Interface For the steps to enable Vehicle Detection, please see 3.1.2 Configuration. - Page 14 For more details please refer to How to enable SSH and collect the print information The URL path is as follows: ftp://hikftp.hikvision.com:400/Product File(Overseas)/00 Oversea Products/01 IP/01 IPC/11 Installation & How to/09 Serial Port & FTP/How to enable SSH and collect the print information.docx...
-
Page 15: Hardware
If you use Hik 34bit, CardID 26bit or SHA-1 26bit wiegand protocol, you can test hardware by Hikvison Access Control Controller. Steps: Connect camera to Hikvision access control controller wiegand interface. Connect 4 pin RS232/RJ45 convertor board to Access Controller debug port and computer USB port. - Page 16 Wiegand Camera ·Operation Manual Power on Access Controller. Access device via SecureCRT software, input the print information that we need: weigenDebugOn Login camera web page select the wiegand protocol you need. If it is CardID 26bit or HIK 34bit protocol, please configure Blocklist &Allowlist in advance. Check Access Controller log.
- Page 17 Wiegand Camera ·Operation Manual non-English characters.