Advertisement
Quick Links
Website:
www.perlesmith.com
TV Wall Mount
Instruction Manual
Model:PSXLF01
Thank you for choosing this Perlesmith product! At Perlesmith
we strive to provide you with the best quality products and
services in the industry. Please share your experience of our
product with others at www.perlesmith.com/pages/reviews if
you are satisfied. Should you have any issues, please don't
hesitate to contact us.
Technical Support:
1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
supportus@perlesmith.com (US/CA)
V1.0
Advertisement
Related Manuals for Perlesmith PSXLF01
Summary of Contents for Perlesmith PSXLF01
- Page 1 Instruction Manual V1.0 Model:PSXLF01 Thank you for choosing this Perlesmith product! At Perlesmith we strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.perlesmith.com/pages/reviews if you are satisfied.
-
Page 2: Weight Restrictions
Minimum VESA pattern: 200mm/8 in.(W)x100mm/4 in.(H) If your TV VESA is greater than 600x400 mm/24x16 in. or less than VESA 200x100mm/8x4in., this mount is NOT compatible. If this mount is NOT compatible, please contact customer service at supportus@perlesmith.com to find a compatible mount. -
Page 3: Supplied Parts And Hardware
DO NOT support line at install into 1-800-556-6806 or drywall alone customer service at Wood Studs Solid Concrete supportus@perlesmith.com (with Drywall) or Concrete Block Tools Needed (Not lncluded) Stud Finder Tape Measure Pencil Drill Hammer in.(5.5 mm) 3/8 in.(10mm) - Page 4 Bolts [Only one bolt size fits your TV] Note: The bolts are shown in accordance with the actual size M6 x 15mm M6 x 35mm [D1] [D2] M8 x 15mm M8 x 25mm [E1] [E2] M8 x 35mm M8 x 50mm [E3] [E4] Supplied Parts and Hardware for Step 2...
- Page 5 Note: The lag screw is shown in accordance with the actual size Lag Screw M8x65mm Washer CAUTION! These anchors are for Wall concrete or brick walls Anchor ONLY. DO NOT use them in drywall or wood studs. Supplied Parts and Hardware for Step 3 to Step 4 Plastic Cover Wrench Front Support...
- Page 6 Correct Note: If necessary, the spacers can be used in multi-layer. If the installation fails after trying various methods, please contact customer service at supportus@perlesmith.com CAUTION: Ensure the TV brackets [03] are EQUALLY CENTERED on your TV AND securely fastened in place.
- Page 7 Option C (For TV with A “Bump”) Spacers may be necessary for 2 holes ONLY. D2/E2/E3/E4 D1/E1 C1/C2/C3 Alternate Spacer Setups Option D For cable interference or inset holes, use spacers [07] to create extra space between the TV and TV brackets C1/C2/C3 D2/E2/E3/E4 Alternate Spacer Setups...
- Page 8 Step 2 Attach the Arm Assembly/Wall Plate [01] to Wall For wood stud installation, follow STEP 2A For concrete installation, follow STEP 2B Step 2A Wood Stud Option WARNING: ●Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1].
- Page 9 2A-3 Drill 4 pilot holes using a 7/32 in.(5.5 mm) diameter drill bit. Make sure the depth is not less than 2 9/16 in.(65mm). 2 9/16 in.(65mm) ø7/32 in.(5.5 mm) 2A-4 Install the arm assembly/wall plate using lag screws [A1] and washer [A2].
- Page 10 2B-1 Position the wall plate template [05] at your desired height, level the wall plate template [05] and mark the pilot hole locations. 2B-2 Drill 6 pilot holes using a 3/8 in.(10mm)diameter drill bit. Make sure the depth is not less than 2 3/4 in.(70mm).
- Page 11 Step 3 Secure Front Support to Arm Assembly Wall Plate Install the plastic cover [04] to front support [02] with the preassembled bolts [S]. Screwdriver Wrench (Not lncluded) Loosen the preassembled bolts [S1] and washers [W] from the back of front support assembly, and keep them for use in step 3-2.
- Page 12 Step 5 Adjust the Tilt and Level Angle CAUTION! Tilt DO NOT over-loosen these four nuts when Wrench adjusting the level angle to prevent the TV from falling off. Loosen Tighten 1. Loosen four tilt nuts [T]. 2. Adjust TV to your desired tilt angle. 3.
- Page 13 Wrench CAUTION! Level DO NOT over-loosen these bolts when adjusting the level angle to prevent the TV from falling off. Screwdriver (Not lncluded) 1. Loosen the two bolts [S1]. 2. Level your TV. 3. Fasten the bolts [S1 to secure TV in place.
- Page 14 Step 6 Manage the Cables...
- Page 15 Thank you again for choosing this Perlesmith product! All of us at Perlesmith do appreciate your product purchase. We hope that you are as happy with your product as we are designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry.
- Page 16 Perlesmith offers products in these categories AV Shelves Anti-tip Straps TV Stands Speaker Stands TV Carts Full Motion Mounts Tilt Mounts Corner Mounts Please remember us when you need one.