Page 1
Instruction Manual V1.0 Model: PSXFK2 Thank you for choosing this Perlesmith product! At Perlesmith we strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.perlesmith.com/pages/reviews if you are satisfied.
Minimum VESA pattern: 200mm/8 in.(W)x100mm/4 in.(H) If your TV VESA is greater than 800x600 mm/31x24 in. or less than VESA 200x100mm/8x4in., this mount is NOT compatible. If this mount is NOT compatible, please contact customer service at supportus@perlesmith.com to find a compatible mount.
DO NOT support line at install into 1-800-556-6806 or drywall alone customer service at Wood Studs Solid Concrete supportus@perlesmith.com (with Drywall) or Concrete Block Tools Needed (Not lncluded) Stud Finder Tape Measure Pencil Drill Hammer in.(5.5 mm) 3/8 in.(10mm)
Page 4
Bolts [Only one bolt size fits your TV] Note: The bolts are shown in accordance with the actual size M6 x 15mm M6 x 35mm [D1] [D2] M8 x 15mm M8 x 25mm M8 x 35mm [E1] [E2] [E3] M8 x 50mm [E4] Supplied Parts and Hardware for Step 2 Arm Assembly/Wall Plate...
Page 5
Note: The lag screw is shown in accordance with the actual size Lag Screw M8x65mm Washer CAUTION! These anchors are for Wall concrete or brick walls Anchor ONLY. DO NOT use them in drywall or wood studs. Supplied Parts and Hardware for Step 3 to Step 4 End Cap Wrench Front Support...
Page 6
Correct Note: If necessary, the spacers can be used in multi-layer. If the installation fails after trying various methods, please contact customer service at supportus@perlesmith.com CAUTION: Ensure the TV brackets [03] are EQUALLY CENTERED on your TV AND securely fastened in place.
Page 7
Option C (For TV with A “Bump”) Spacers may be necessary for 2 holes ONLY. D2/E2/E3/E4 D1/E1 C1/C2/C3 Alternate Spacer Setups Option D For cable interference or inset holes, use spacers [07] to create extra space between the TV and TV brackets C1/C2/C3 D2/E2/E3/E4 Alternate Spacer Setups...
Page 8
Step 2 Attach the Arm Assembly/Wall Plate [01] to Wall For wood stud installation, follow STEP 2A For concrete installation, follow STEP 2B Step 2A Wood Stud Option WARNING: ●Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws [A1].
Page 9
2A-3 Drill 4 pilot holes using a 7/32 in.(5.5 mm) diameter drill bit. Make sure the depth is not less than 2 9/16 in.(65mm). 2 9/16 in.(65mm) ø7/32 in.(5.5 mm) 2A-4 Install the arm assembly/wall plate using lag screws [A1] and washer [A2].
Page 10
2A-1 Position the wall plate template [05] at your desired height, level the wall plate template and mark the pilot hole locations. 2A-2 Drill 6 pilot holes using a 3/8 in.(10mm)diameter drill bit. Make sure the depth is not less than 2 3/4 in.(70mm).
Page 11
Step 3 Secure Front Support to Arm Assembly Wall Plate Install the end caps [04] to front support [02] with the preassembled bolts [S]. Screwdriver Wrench (Not lncluded) Loosen the preassembled bolts [S1] and washers [W] from the back of front support assembly, and keep them for use in step 3-2.