Page 1
14ft x 17ft JumpPOD Oval Got a Problem building your trampoline? Call us on 0344 800 4060 and we can help Patent no: DE602006006495D1, EP1721640B1 and US7628731 WARNING: Read these assembly instructions carefully before attempting to assemble or use this product. Keep...
IMPORTANT PRECAUTIONS VXUIDFH 1 user DOORZHG DW DQ\ RQH WLPH 7KLV FDQ UHVXOW LQ VHULRXV LQMXU\ WR KHDG QHFN DUPV RU OHJV JUMPING INSTRUCTIONS Fundamental Bounce Knee Drop Hand and Knee Drop Start bouncing from a standing Start bouncing from a standing Start from a standing position with your head erect and your eyes on the position, keeping your eyes on the...
BUILDING YOUR TRAMPOLINE 1. This is a 2 person build. 2. Time for build is approximately 2 hours. 3. Choose a good location: (wood chippings, sand or grass). (7.3m) from ground level, away from wires, trees and other possible hazards. (2.5m) around sides, away from walls, fences, structures, tarmac and other hard surfaces and play areas.
PARTS LIST Part Part Part Part Part Description: Description: Description: Description: Description: Top tube with Top tube with Top tube with Top tube with Top tube with A marking D marking E marking C marking B marking Quantity: 2 Quantity: 2 Quantity: 2 Quantity: 2 Quantity: 2...
STEP 1 : ASSEMBLING THE FRAME You will need the following parts to complete section 1: - Part A 2 x Top tube with A marking - Part B 2 x Top tube with B marking - Part C 2 x Top tube with C marking - Part D 2 x Top tube with D marking 2 x Top tube with D marking - Part E...
Page 8
Insert 1 end of W-leg partially into Connector A. Next place feet either side of POD-Connector B. Then pull other end of W-leg into POD-Connector B. (You will need to use force for this step) Now push down on W-leg so inserted fully in each POD-connector.
Page 9
Colored Locate the V-rings with coloredwebbing. webbing These will be at 180 to each other. Slot one of the springs onto one of the colored webbing V-rings as shown. Important: springs must be slotted on the right way around.
Page 10
This diagram shows the initial order of spring attachment. = Top spring hole, = Bottom spring hole = Bot , , , , , , , , , , , Important: Attach the springs in Important: Attach the springs in the order shown in the diagram.
Page 11
STEP 4 : FITTING THE FRAME PAD This step will require 2 people. Lay the frame pad - Part K out over the edge of the frame with the ties facing downwards. Align the openings in the frame pad with the POD-connector's on the frame.
Page 12
STEP 5 : FITTING THE ENCLOSURE TUBES Top enclosure tube You will need the following parts to complete step 5: 8 x Top enclosure tubes - Part M Bottom enclosure tube 8 x Bottom enclosure tubes - Part L 8 x Self tapping screws and washers - Part P Self tapping screw and washer You will also need a cross-head screwdriver (not supplied).
Page 13
Slot the bottom enclosure tube into the tubes in the POD-connector tubes visible through the slots in the frame pad. Assemble the remaining enclosure tubes using the self tapping screws and the cross-head screwdriver. Slot the remaining enclosure tubes into the remaining POD-connector’s on the frame.
Page 14
STEP 6 : FITTING THE ENCLOSURE NETTING You will need the following parts to complete step 6: 2 x Black G4 poles - Part N Black G4 poles 1 x Enclosure netting - Part O Enclosure netting Lay the enclosure netting out on the trampoline. Find the sleeves that run along the top of the enclosure netting.
Page 15
Slot one of the Black G4 poles through three of the sleeves on the top of the enclosure netting. Slot the remaining Black G4 poles through the three other sleeves on the top of the enclosure netting. You will now join the two ends of the Black G4 poles together with the fitted pole connectors, this will require two people.
Page 16
You may need to slide the connected poles around in the nettings sleeves until the thin black sections are aligned with the gaps between sleeves. Stand on the trampoline and insert one of the exposed sections of the Black G4 pole into a plastic grip on top of one of the enclosure tubes.
Page 17
STEP 7 : ATTACHING THE BOTTOM OF THE NET You will need the following parts to complete step 7: 8 x Cords - Part R. Push 1 end of a cord through a hole in the bottom of the netting. Then tie this end to a V-ring on the bed.
Page 18
USING THE TRAMPOLINE Before using your trampoline, check again that there is enough clearance around it. Maintain a clear space of 2.5 metres (8.2 feet) on all sides of 2.5m the trampoline. Also check that the area is free from walls, structures, fences, tarmac and other hard surfaces and other play areas.
V legs 7” length springs Screw + spring washer PP rope 7” length gold springs Plas c caps for connector For a full range of accessories and replacement parts call 0344 800 4060 or visit our web site at: www.jumpking.eu...
Need help?
Do you have a question about the US7628731 and is the answer not in the manual?
Questions and answers