Using The Stylistic Ct2000 Series Ce Tablet; Before Setting Up The Tablet; Powering Up The Tablet; No Application Has Been Installed - Fujitsu Stylistic CE CT2000 Series User Manual

Using the Stylistic CT2000 Series CE Tablet

This chapter covers the fundamental concepts, basic
system operation and use, and system functions of the
Stylistic CT2000 Series CE Tablet. You should familiarize
yourself with this information before you attempt to
operate the system.

BEFORE SETTING UP THE TABLET

Before you set up your tablet, there are two important
steps to perform:
• The display can be damaged with improper use. We
highly recommend that you install a screen protector
on your system. Screen protectors are available as
optional accessories for your tablet. (For part
numbers and ordering information, go to the Fujitsu
Web site at: us.fujitsu.com/computers.) To install a
screen protector, refer to "Protecting the Display" on
page 33.
• The system should be charged for a full 24 hours
prior to first using it. The 24-hour period ensures
that the main and backup batteries are fully charged.

POWERING UP THE TABLET

Follow the procedure below to start the Stylistic CT2000
Series CE Tablet if it is in the Off state. When you first
receive your system, it may or may not be in the Off
state. Under normal circumstances, the system should
not be in the Off state.
Before you begin, confirm whether the system is in the
Off state. To do so, perform the following steps:
1. Ensure that a charged battery is installed.
2. Press the Power button at the top left of the keypad
for one to two seconds. If the LED is not lit, the
system is in the Off state and it is safe to perform this
procedure. If it is lit, do not perform this procedure.
3. Remove the battery pack from your system by sliding
the two battery release latches toward the unlatch
icon , and sliding the battery out of the bay.
4. Using the tip of your pen, slide the Power switch
located inside the battery bay into On position.
5. Slide the battery back into the bay. The battery
release latch at the bottom will click into place, but
you must manually lock the upper latch, otherwise
the battery will be unusable and the system will not
power on.
6. Press the Power button on the keypad for one to two
seconds.
After performing initialization, the system starts the
operating system.
U s i n g Y o u r S t y l i s t i c C T 2 0 0 0

"NO APPLICATION HAS BEEN INSTALLED"

If you have not added any new programs using the
backup utility since the system was new , you will receive
a message the next time you power the system on after
having reset the system with the Power switch. (See
Using the Stylistic CT2000 Series CE Tablet on page 15 for
more information.) The message will state "No applica-
tion has been installed." When this occurs, press the
keypad [BKS] key.
After pressing the [BKS] key, you will be prompted to
calibrate the pen and set the date and time. When the
setting menu appears, tap on "Desktop" in the menu.

"CONTENTS OF MEMORY HAS BEEN LOST"

If you have added any new programs using the backup
utility, you will receive a message the next time you
power the system on after having reset the system with
the Power switch. (See Using the Stylistic CT2000 Series
CE Tablet on page 15 for more information.) The message
will state "The contents of memory has been lost".
Click [Restore] to recover the application program.

SHUTTING DOWN THE SYSTEM

Note that shutting down the system is not recommended
under normal circumstances, and should only be
performed if the system is to be stored for a long period
of time. If the system freezes up, use the procedure for
"Resetting the System", below.
• Use the Power switch to shut off the
system only if you have no alternative.
• If the system is shut down using the
Power switch, data and programs that are
stored in RAM will be lost.
Follow these steps to turn off your system:
1. If possible, save your work and close all running
programs.
2. Remove the battery pack from your system by
sliding the two battery release latches toward the
unlatch icon , and sliding the battery pack out
of the bay.
3. Using the tip of your pen, slide the Power switch
located inside the battery bay into Off position. The
system is now in the Off state.
4. When you are ready to restart your tablet, follow the
steps for "Powering Up the Tablet".
15