Iset-Up Menu Options; Set-Up Power Save - FujiFilm Finepix S3000 Owner's Manual

g USING SET–UP
I SET–UP Menu Options
Default
Settings Display
setting
IMAGE DISP. ON/OFF ON
POWER SAVE ON/OFF OFF
FORMAT OK –
) BEEP LOW/HIGH/OFF LOW
DATE/TIME SET –
USB MODE (/UPC
(
LANGUAGE
ENGLISH
VIDEO SYSTEM
NTSC/PAL —
q RESET OK —
78
Explanation
This option specifies whether or not an image checking screen (photography
results) is displayed after you take a shot.
The photographed image is displayed for a few moments and then
automatically recorded.
In continuous shooting, the photography results are displayed for a set time
before being automatically recorded even if this option is set to "OFF".
This function temporarily switches the screen off if the camera is not used for
approximately 30 seconds. See P.79 for details.
Erases all files. See P.80 for details.
Sets the volume of the tone emitted when the camera controls are used.
Use this option to correct the date or time. See P.18 for details.
Selects the function when the camera is connected to a PC.
See P.97 for details.
Use this setting to specify the language used for LCD monitor display.
Specifies whether video output is set to NTSC or PAL.
Resets all the camera settings other than the date and time, language and
video output settings to the factory default values set at shipment. Pressing "c"
displays a confirmation screen. To reset the settings, press the "MENU/OK"
button.
POWER SAVE
SET–UP
ＳＥＴ−ＵＰ ＳＥＴ−ＵＰ １／２ １／２
ＩＭＡＧＥ ＤＩＳＰ． ＩＭＡＧＥ ＤＩＳＰ． ＯＮ ＯＮ
ＰＯＷＥＲ ＳＡＶＥ ＰＯＷＥＲ ＳＡＶＥ
ＯＦＦ ＦＦ
ＦＯＲＭＡＴ ＦＯＲＭＡＴ ＯＫ ＯＫ
ＢＥＥＰ ＢＥＥＰ
ＬＯＷ ＬＯＷ
ＤＡＴＥ／ＴＩＭＥ ＤＡＴＥ／ＴＩＭＥ ＳＥＴ ＳＥＴ
ＯＫ ＯＫ ＳＥＴ ＳＥＴ ＢＡＣＫ ＢＡＣＫ ＣＡＮＣＥＬ ＣＡＮＣＥＬ
hPower saving "OFF" (default setting)
The camera does not use measures such as
"sleep" to reduce power consumption. However, if
the camera is not used for approximately 2 minutes,
this function automatically switches the camera off.
hPower saving "ON"
Power consumption is kept to a minimum to
prevent battery depletion.
i If the camera is not used for approximately 30
seconds, the screen switches off temporarily
to reduce power consumption (Sleep mode).
i Once the camera is in Sleep mode, if it is left
unused for a further 90 seconds, it is
automatically switched off.
i The charging time for the flash increases
slightly because the flash charging power is
reduced.
Bebeep
When the camera is in sleep mode, pressing the
Shutter button down halfway brings the camera
back to full operational mode. This is a useful
feature as it allows you to take pictures more
quickly than switching the camera off and then
on again. You can also take a picture by pressing
the Shutter button all the way down.
G
!
Operation can also be restored by pressing buttons
other than the Shutter button.
N N
To restore power to the camera
Turn the Power switch to
"OFF" briefly and then
back to "q".
5
79