Page 2
Instruction book ......3–12 Before using the appliance for the first time, please read the safety advice CNT 說明手冊 ........13–22 第一次使用本機之前,請先閱讀 安全建議 คู ่ ม ื อ แนะนำ � ก�รใช้ ง �น ..23–32 ก่ อ นใช้ อ ุ ป กรณ์ เ ป็ น ครั ้ ง แรก กรุ ณ า อ่...
Page 3
Components 10. Measuring scoop Main indicator light 11. Filter holder Temperature indicator light 12. Filter sieve: Hot-water/steam selector button a. 1 cup On/Off switch b. 2 cups Operating dial for espresso /steam 13. Water container Steam tube 14. Water container lid Steam nozzle with milk frother 15.
• To reduce the risk of fire or electric shock, do not attempt to remove the outer cover. There are no user-serviceable parts inside. Repair should be done only by authorized Electrolux technicians. • If the power supply cord is damaged, it should be replaced by a qualified technician from Electrolux.
Operating Dial The operating dial has three settings: Dispensing steam/hot water via the steam nozzle Pump switched off / neutral position Pump switched on: dispensing espresso via the boiler outlet 4. As soon as the operating dial is turned from its neutral position, either the steam nozzle or boiler outlet will open, and steam or hot water will be emitted. Before Using For The First Time Before the appliance is used for the first time, all detachable parts must be thoroughly cleaned as described in the section “Care and Cleaning”. Refit the drip tray and drainer...
Operation Filling with water Fill only with fresh water on a daily basis; make sure that the water container is cleaned at regular intervals. Do not switch the appliance on unless the water container is filled. Lift up the water container lid and flip it back. Lift out the water container.
Page 7
• To unlock and remove the filter holder, turn it to the left, i.e. clockwise. • Do not remove the filter holder while the appliance is in use, since the filter holder is under pressure. Once the brewing cycle is complete, wait around 30 seconds before removing the filter holder. Hot-water/steam selector button This selector allows you to choose either hot water or steam. • To dispense hot water, the button must be in its released position. The hot water can now be drawn through either the boiler outlet or the steam outlet. •...
Page 8
Filling the filter sieve with ground coffee • Remove the preheated filter holder (Caution: the filter holder is hot). • Fill with finely ground coffee: 1 cup = 1 level measuring scoop 2 cups = 2 level measuring scoops • Note: if the filter holder is over- filled, it will not lock properly under the boiler outlet. 2 level measuring scoops is the maximum quantity. • Use the measuring scoop to distribute the ground coffee evenly and press it down lightly. Any excess coffee powder on the rim of the filter holder must be removed. Removing the used grounds •...
Preparation Espresso • Fill the container with water. • Insert the plug into a suitable wall outlet and use the On/Off switch to turn on the appliance. The main indicator light and temperature indicator light will be turn on. • Set the selector to the hot-water position (button released). • Preheat the filter holder and the cup(s). • Remove the filter holder, fill with ground coffee and re-attach it. • Place the cup(s) underneath the outlets. • When the temperature indicator light turns off, turn the operating dial to position . The espresso is now delivered straight into the cup(s). • Once the cup(s) are full, turn the valve selector to its neutral position to switch the pump off. • Wait for approximately 30 seconds before detaching the filter holder and removing the coffee grounds. •...
Dispensing Steam This appliance is designed to dispense steam for heating up milk or other beverages through the steam nozzle, and also for the frothing of milk when making cappuccino. To dispense steam, push the hot-water/steam selector button in. After a brief heating period, the temperature indicator light will turn off. Steam can now be drawn from the steam nozzle by turning the operating dial to position .
Reheating beverages • Push the hot-water/steam selector button in. • Insert the steam nozzle into the liquid to be reheated and turn the operating dial to the position. • Once the liquid has reached the desired temperature turn the operating dial back to its neutral position. • When steam is no longer needed, release the selector button again. Care and Cleaning • Before cleaning the espresso maker, ensure it is disconnected from the power supply and has cooled down completely. • To avoid the risk of electric shock, do not clean the appliance with water and do not immerse it in water. • Do not use abrasives or harsh cleaning solutions. • Before cleaning the appliance, and also in the case of the appliance remaining unused for an extended period of time, the remaining water in the container should be drained completely.
Descaling • Depending on the water quality (lime content) in your area as well as the frequency of use, all thermal household appliances using hot water need descaling (i.e. removal of lime deposits) on a regular basis to warrant proper functioning. • For descaling, any commercially available citric- acid-based descaling agent for coffee makers may be used. • Pour the descaling solution into the water container. • As described in the section “Making espresso”, (but without any ground coffee being placed in) and, with the filter insert removed, switch the appliance on and let it run, cup for cup, through the filtration cycles. Allow 5 minutes between each cycle for the descaling agent to take effect. • To clean the appliance after descaling, fill the water container twice with clean water and let each filling run through its filtration cycles until the container is nearly empty.
Page 36
Share more of our thinking at www.electrolux.com Product specifications and colours are subject to changes and vary from country to country APAC-EES200E_5503S-IFU-AP-5...