Package, Transport, Storage; Delivery; Transport; Storage - Homa C240W F Original Instruction Manual

3.3.2. Motor
The motor consists of a stator and a motor shaft with the
rotor package. The electrical supply line is designed for
the maximum mechanical power according to the curve
or rating plate of the pump. The cable entries and the line
are sealed watertight against pressurised water for the
conveying medium. The shaft bearing is provided via ro-
bust, maintenance-free and permanently-lubricated roller
bearings.
General Motor Data
Operating mode for temperature of medi-
um up to 35°C
Operating mode for temperature of medi-
um up to 60°C
Permitted medium temperature
Protection type
Standard cable length
Voltage
Warning of rotating impeller!
Do not touch the rotating impeller or reach through
the pressure joints into the pump chamber! When
in operation, never reach into the pump chamber or
towards the rotating parts. Before maintenance or
repair work, shut down the machine and have the
rotating parts come to a standstill.
3.3.3. Monitoring Equipment
Motor Type Motor Version
...W... 230V / 1Ph
...F Flat suction
Shallow Water Pump
Design with sensor connection, sensor cover, 10m con-
nection cable. The 1Ph pumps are also equipped with in-
tegrated capacitors and plugs.
Temperature Gauge
All pumps are equipped with a temperature gauge set in
the motor windings. This shuts down the pump if it over-
heats. After the pump has cooled down, it switches on
again automatically.
Motor Cooling
With the cooling jacket with compression connection
above, the motor cooling is sufficient even in sloshing op-
erations.
3.3.4. Sealing / Gasket Housing
Sealing is provided by three axial shaft seals.
3.3.3. Pump housing
The pump housing is fitted with a discharge outlet
R 1 ¼" AG.
3.3.4. Blade wheel
The blade wheel is fastened on the motor shaft and is
driven by it. The blade wheel is an open multivane impel-
ler.
S1
S2 20 min / S3 40%
60°C
IPX8
10 m
230V / 1Ph / 50Hz

4. Package, Transport, Storage

4.1. Delivery

On arrival, the delivered items must be inspected for dam-
age and a check made that all parts are present. If any
parts are damaged or missing, the transport company or
the manufacturer must be informed on the day of delivery.
Any claim made at a later date will be deemed invalid.
Damage to parts must be noted on the delivery or freight
documentation.

4.2. Transport

The product is delivered by the manufacturer/shipping
agency in suitable packaging. This normally precludes the
possibility of damage occurring during transport and stor-
age. The packaging should be stored in a safe place if the
location used is changed frequently.

4.3. Storage

Newly supplied products are prepared that they can be
stored for at 1 year. The product should be cleaned thor-
oughly before interim storage.
The following should be taken into consideration for stor-
age:
• Place the product on a firm surface and secure it
against falling over.
• We recommend a dry, frost-protected room with a
temperature of between 5 °C and 25 °C for storage.
• The machine must be protected from direct sunlight,
heat, dust, and frost.
• If the product has been stored for a long period of
time it should be cleaned of impurities such as dust
and oil deposits before start-up
If these rules are observed, your product can be stored
for a longer period. Please remember that elastomer parts
and coatings become brittle naturally. If the product is
to be stored for longer than 6 months, we recommend
checking these parts and replacing them as necessary.
Please consult the manufacturer.

4.4. Returning to the supplier

Products which are delivered to the plant must be clean
and correctly packaged. In this context, clean means that
impurities have been removed and decontaminated if it
has been used with materials which are hazardous to
health. The packaging must protect the product against
damage. Please contact the manufacturer before return-
ing!
EngliSH | 25