Texas Instruments ADC12DL3200 User Manual
  1. Manuals
  2. Brands
  3. Texas Instruments Manuals
  4. Motherboard
  5. ADC12DL3200
  6. User manual

Texas Instruments ADC12DL3200 User Manual

Hide thumbs Also See for ADC12DL3200:
Table of Contents

Advertisement

Quick Links

Download this manual
ADC12DL3200 Evaluation Module
User's Guide
Literature Number: SLAU776
May 2018

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ADC12DL3200 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Texas Instruments ADC12DL3200

Summary of Contents for Texas Instruments ADC12DL3200

  • Page 1 ADC12DL3200 Evaluation Module User's Guide Literature Number: SLAU776 May 2018...

  • Page 2: Table Of Contents

    Capture Data Using the HSDC Pro Software ......................Device Configuration ......................Tab Organization ......................Low-Level Control ................Troubleshooting the ADC12DL3200EVM ................Optional ADC12DL3200EVM Configurations ..............Modifying the EVM for Optional Clocking Support Contents SLAU776 – May 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...
  • Page 3 HSDC Pro GUI ................3-1. Configuration GUI: Low-Level View Tab ....................B-1. External CLK Configuration List of Tables ......................3-1. Low-Level Controls ......................A-1. Troubleshooting SLAU776 – May 2018 List of Figures Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...

  • Page 4: Preface

    EVM are synonymous with the ADC12DL3200EVM. The ADC12DL3200 is a dual-channel, 12-bit ADC, capable of operating at sampling rates up to 3.2 Giga- samples per second (GSPS) in dual-channel mode, or 6.4 GSPS in single-channel mode. The ADC12DL3200EVM device output data is transmitted over a high-speed LVDS interface.
  • Page 5 ADC device. LVDS data rates of 1600 Mbps down to 400 Mbps are supported. In the following sections of this document, the ADC12DL3200EVM is referred to as the EVM and the ADC12DL3200 device is referred to as the ADC device. Related Documentation Technical Reference Documents •...

  • Page 6: Equipment

    (Differential Connector (Differential Inputs) Clock) (Differential Inputs) (Bottom Side) Inputs) VINB VINA (Single-Ended Input) (Single-Ended Input) CLKIN0 (Optional 10-MHz External Reference) Figure 1-1. EVM Feature Locations Equipment SLAU776 – May 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...

  • Page 7: Required Equipment

    One low-noise signal generator. TI recommends models similar to the analog input source. • A bandpass filter for the DEVCLK input. TI recommends a filter similar to the analog-input path filter. SLAU776 – May 2018 Equipment Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...

  • Page 8: Setup Procedure

    Figure 2-1. EVM Test Setup NOTE: The HSDC Pro software must be installed before connecting the TSW14DL3200EVM to the PC for the first time. Setup Procedure SLAU776 – May 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...

  • Page 9: Install The High Speed Data Converter (Hsdc) Pro Software

    ADC12DL3200EVM. Providing the ADC12DL3200EVM with 12-V may result in immediate damage. Leave the power switches in the off position until directed later. SLAU776 – May 2018 Setup Procedure Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...

  • Page 10: Connect The Signal Generators To The Evm (*Rf Outputs Disabled Until Directed)

    Turn on the RF signal output of the signal generator connected to VIN. If external clocking is used, turn on the RF signal outputs connected to DEVCLK and LMKCLK. Setup Procedure SLAU776 – May 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...

  • Page 11: Open The Adc12Dl3200Evm Gui And Program The Adc And Clocks

    EVM features, with user-friendly controls and a low-level tab for directly configuring the registers. The EVM has three configurable devices: the ADC12DL3200,LMK04828, and LMX2582. The register map for each device is provided in the device data sheets.

  • Page 12: 2.10 Calibrate The Adc Device On The Evm

    3. Select Foreground, Background, or Low Power Background calibration mode using the Sampling and Calibration Mode drop-down menu on the EVM tab. Setup Procedure SLAU776 – May 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...

  • Page 13: 2.11 Open The Hsdc Software And Load The Fpga Image To The Tsw14Dl3200Evm

    ) as 5400M or the desired output sample rate. This number (SAMPLE) must be equal to the actual sampling rate of the device, and must be updated if the sampling rate changes. SLAU776 – May 2018 Setup Procedure Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...

  • Page 14: 2.12 Capture Data Using The Hsdc Pro Software

    Select Size of Analysis Window Enter Device Output Sample Rate Click for Decimation and NCO Settings Enter Target Input Frequency Figure 2-4. HSDC Pro GUI Setup Procedure SLAU776 – May 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...

  • Page 15: Device Configuration

    At any time, the controls in Table 3-1 can be used to configure or read from the device. Figure 3-1. Configuration GUI: Low-Level View Tab SLAU776 – May 2018 Device Configuration Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...
  • Page 16 Perform a generic read or write command to the device shown in the Block drop-down menu using read or write register buttons the address and write data information Device Configuration SLAU776 – May 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...

  • Page 17: Troubleshooting The Adc12Dl3200Evm

    • Use the free FT_PROG software from FTDI chip and verify that the onboard FTDI chip is able to connect to the EVM programmed with the product description ADC12DL3200. • Verify that the TSW14DL3200EVM is properly connected to the PC with a mini USB 3.0 cable HSDC Pro software is not and that the board serial number is properly identified by the HSDC software.

  • Page 18: B Optional Adc12Dl3200Evm Configurations

    The LMX2582 and LMK04828 may be reconfigured to exercise more features, but this EVM is not intended to be a full evaluation platform for these devices. For a full evaluation platform, see the LMK04828 tool folder LMX2582 tool folder. Optional ADC12DL3200EVM Configurations SLAU776 – May 2018 Submit Documentation Feedback Copyright © 2018, Texas Instruments Incorporated...
  • Page 19 STANDARD TERMS FOR EVALUATION MODULES Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms set forth herein.
  • Page 20 FCC Interference Statement for Class B EVM devices NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 21 【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの 措置を取っていただく必要がありますのでご注意ください。 1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用 いただく。 2. 実験局の免許を取得後ご使用いただく。 3. 技術基準適合証明を取得後ご使用いただく。 なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。 上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ ンスツルメンツ株式会社 東京都新宿区西新宿６丁目２４番１号 西新宿三井ビル 3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page 電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧ください。http:/ /www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page 3.4 European Union 3.4.1 For EVMs subject to EU Directive 2014/30/EU (Electromagnetic Compatibility Directive): This is a class A product intended for use in environments other than domestic environments that are connected to a low-voltage power-supply network that supplies buildings used for domestic purposes.
  • Page 22 Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief in any United States or foreign court. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2018, Texas Instruments Incorporated...
  • Page 23 IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are developing applications that incorporate TI products;...
  • Page 24 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments ADC12DL3200EVM...

Table of Contents