Subscribe to Our Youtube Channel
Related Manuals for Polivac GASS38KOH
Summary of Contents for Polivac GASS38KOH
- Page 1 OLIVAC URNISHER 38” GAS BUFFING MACHINE GASS38KOH Operations Manual & Trouble Shooting Guide...
-
Page 2: Table Of Contents
OWNER’S MANUAL TABLE OF CONTENTS Introduction ………………………………………….………………………. 3 Use & Care ………………………………………………….………………… 3 Safety Precautions ………………………………………………………… 3 Unpacking Instructions ………………………………….………………. 4 Machine Preparation ………….…………………………….……………. 4 Starting the Engine ………………………………………….……………. 4 Operation of Buffer …………………………………………..……………. 4 Stopping the Engine ……………………………………….……………… 4 Maintenance ……………………………………………………….…………... -
Page 3: Introduction
This will cause oil to seep into the carburettor and head of the engine, which will cause excessive smoking and damage to the engine and regulator system. USE AND CARE Before using any new equipment, Polivac strongly recommends following safety precautions for all owners and operators of gas-powered equipment. SAFETY PRECAUTIONS 1. -
Page 4: Unpacking Instructions
UNPACKING INSTRUCTIONS Polivac gas buffers comes packaged in a palletised box designed to protect and secure the machine during transportation. The machine is supplied with no gas cylinder. Before signing the delivery receipt, inspect the packaging for damage (Remove box and check machine for damage). If damage is evident, note the damage on the delivery receipt and contact your supplier. -
Page 5: Maintenance
MAINTENANCE 1. Prior to Use: • Check the oil level and condition. • Clean and/or replace engine and carburettor filters. • Check pad condition. • Clear engine cooling vanes. • Check all gas lines and fittings for damage, cuts or leaks. 2. -
Page 6: Do's & Don'ts
IMPORTANT NOTICE Polivac would like to direct your attention to the following issues so that correct and safe operation of your gas-powered floor buffer is achieved. The superior performance of gas buffers has led to an increased demand for the use of this type of floor maintenance equipment. This highlights the need for responsible manufacturers, owners and operators to stress the importance of safety. -
Page 7: Machine's Top Diagram
38” GAS BURNISHER TOP PARTS DIAGRAM – GASS38/GASS38KOH... -
Page 8: Machine's Top Parts List
TOP PARTS LIST – GASS38/GASS38KOH CODE DESCRIPTION CODE DESCRIPTION GGS007 Battery VPV094 Clamp GGS003 Battery Holder STR058 SLB030 Bolt GAS069 Washer AAG236 Washer GGS028 Motor Base VPV605 Handgrip VPV251 Gasket GGS002 Handle Assy. GGS001 Base AAF140 AAG236 Washer GAS041 Spring Washer... -
Page 9: Machine's Base Diagram
38” GAS BURNISHER BASE PARTS DIAGRAM... -
Page 10: Machine's Base Parts List
BASE PARTS LIST – GASS38/GASS38KOH CODE DESCRIPTION CODE DESCRIPTION PPR002 Continental Trim GAS031A Circlip GGS001 Base AAG470 Washer x 5 AAA564 Screw GGS019 Spindle / Shaft AAG236 Washer GGS021 Bearing GAS041 Washer GSS036 52mm Circlip GGS062 Bolt Wheel VPA570 Bearing... -
Page 11: Warranty Policy
Use of non-approved chemicals and detergents in the product will void the warranty. 10. Products that have been modified are not covered by warranty. 11. Products that have not been serviced at their recommended intervals by an authorised Polivac Service Centre or Agent are not covered by warranty 12. - Page 12 50 YEARS EXCELLENCE FOR OVER...
Need help?
Do you have a question about the GASS38KOH and is the answer not in the manual?
Questions and answers