Related Manuals for ETENON Fitness PC16
Summary of Contents for ETENON Fitness PC16
- Page 1 ’ OWNER S MANUAL Standing Calf Raise CAUTION Please read all instructions in this manual before use the equipment and keep the manual well.
- Page 2 In order to a void human injuri es and property dam age , before th e u e s of this series equipment please read the following mportant notices 1. Before u se o the e quipm ent please read this Ow ner’s Manual carefully The equipment should be assembled and used strictly following the relevant...
- Page 3 equipment and ca n not increase he eight of weight stack by use of other manufacturers’ weight stack plate . ( Apply to single station w h it ca 9. Child and pet are n ot lowed to be too lo c se to he equipment while t s in using 10.
- Page 4 Upper shield Swing span Adjusting bracket Floor stander Shoulder pads Front shield Foot Bottom Frame...
- Page 5 1. When strip f the wrappage around the surface of equipment, should be a c reful do not hurt the ma chine with knife atches on the surface 2. When moving this equipment a suffi i c ent number of personnel should be used to prevent the equipment from col lision or to avoid the injurie...
- Page 6 force Make cer ain that he equipmen t is w ithout an ab normity before normally use the machine If something unu ual is found with the equip ment that , it is necessary to check the equipmen t carefully identify the probl s and reinstall it .
- Page 7 Assembly step1 Steps No. Description Specifications Qty Transverse joint frame Middle bottom Frame Plain washer Φ24*Φ13*2.5 Spring washer Hex socket head cap screw M12*30 Doorframe...
-
Page 8: Description Specifications Qty
Assembly step2 Steps No. Description Specifications Qty Front support frame Middle bottom Frame Floor stander Plain washer Φ20*Φ10.5*2 Spring washer Hex socket head cap screw M10*30 Hex socket head cap screw M10*25... - Page 9 Assembly step3 Steps No. Description Specifications Qty Load-bearing frame Swing span Adjusting bracket Axle 2 Gas spring cylinder Plain washer Φ20*Φ10.5*2 Spring washer Hex socket head cap screw M10*30...
- Page 10 Assembly step4 Steps No. Description Specifications Qty Front support frame Load-bearing frame Swing span Axle 1 Circlips for shaft Φ25...
-
Page 11: Countersunk Hex Socket Screws M10*70
Assembly step5 Steps No. Description Specifications Qty Front support frame Middle bottom Frame Foot frame Plain washer Φ20*Φ10.5*2 Nylon insert lock nut Spring washer Hex socket head cap screw M10*30 Countersunk hex socket screws M10*70... -
Page 12: Spring Washer M8
Assembly step6 Steps No. Description Specifications Qty Swing span Shoulder pads Plain washer Φ16*Φ8.4*1.6 Spring washer Hex socket head cap screw M8*25... -
Page 13: Hex Socket Head Cap Screw M5*50
Assembly step7 Steps No. Description Specifications Qty 20lb weight stack plate Cable set 10lb counterweight Spring washer Hex socket head cap screw M8*20 Doorframe Guild rod stator Big washer Φ24*Φ8.4*2 Rod end cover Rubber bumper Cage nut Rubber bumper Φ38*Φ22*8 Guide rod... -
Page 14: Hex Socket Head Cap Screw M6*16
Assembly step8 Steps No. Description Specifications Qty Plain washer Φ16*Φ8.4*1.6 Hex socket head cap screw M8*20 Doorframe Upper shield Shield fixation column Hex socket head cap screw M6*16 Plain washer Φ12*Φ6.4*1.6 Front shield... - Page 15 Cable Route Diagram Wrong Correct L plate L plate...
- Page 16 Exploded View...
- Page 17 Exploded List Description Specifications Front support frame Transverse joint frame Middle bottom Frame Floor stander Load-bearing frame Swing span Adjusting bracket Foot frame Adjusting bolt column Shoulder pads Adjustment handle bracket Small shaft Axle 1 Axle 2 Nylon rollers Gas spring cylinder 20lb weight stack plate Cable set Steps rolling bearing...
-
Page 18: Table Of Contents
Exploded List Description Specifications Nylon insert lock nut Hex socket head cap screw M10*75 Spring washer Hex socket head cap screw M10*30 Hex socket head cap screw M10*25 Countersunk hex socket screws M10*70 Countersunk hex socket screws M6*25 Slotted set screws with cone point M4*5 Circlips for shaft Φ25... - Page 19 Basic Maintenance 1. Clean the seat pad b ck pad and cushion with warm w ater and soft cloth order to avoid the w at erosion t o the e s component 2. Clean the frame with warm water and soft cloth . 3.
- Page 21 Weight stack label instructions 1 Wipe front surface of weight stack 2 Peel off back sheet adhesive side from label and make sure that the label remains attached to the application tape 3 Aline the center hole of label with the weight stack center hole 4 Line up the first label to hole on top plate 5 Make sure label is straight and slowly press into place...