Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Rittal CMC-TC Master II
Summary of Contents for Rittal CMC-TC Master II
- Page 1 DK 7320.005 CMC-TC Master II Instruction manual A29290 07 IT 74...
-
Page 2: Table Of Contents
View, store and delete log file... 18 System prerequisites......5 7.5.9 Configure overview window ....19 Scope of supply........5 7.5.10 Update CMC-TC Master II ....19 Accessories ......... 5 Configuring alarm conditions .... 20 3.6.1 Required accessories......5 Configuring the Webcam images..21 3.6.2... -
Page 3: Notes On The Documentation 1
CMC-TC Master II may be performed only by instructed personnel. 1.1 Associated documents − Observe the valid regulations for the electrical... -
Page 4: Device Description
CMC-TC Master II. 3.1 Housing 3.3 Network characteristics The CMC-TC Master II is installed in its own hous- The Master II has a 10/100BaseT Ethernet network ing. The supplied self-adhesive plastic feet can be connection supported with the following protocols: used to place the device on component shelves. -
Page 5: System Prerequisites
• Check the packaging carefully for any signs of IEC plug con- damage. nection cable 7200.211 Country variant Quantity Description (GB) IEC plug con- CMC-TC Master II with network nection cable interface RJ -45 socket (10/100 7200.210 Country variant Yes, BaseT) (F/B) once for Top-hat rail brackets... -
Page 6: Optional Accessories
Assembly on a 2 U component shelf 4.1 Assembly instructions CMC-TC Master II Install the CMC-TC Master II in an enclosure or in a Screwed adjustable feet suitable housing system so that it also has addi- 2 U component shelf with holes, model no. 7119.400 tional protection from external effects. -
Page 7: Installation 5
5.4 Connecting the programming inter- face 5.2 Connecting the power supply If you want to configure the CMC-TC Master II, for example, using a notebook, you can connect both devices with each other using the serial interface (COM1). -
Page 8: Commissioning
6 Commissioning Commissioning Once you have assembled the CMC-TC Master II and installed all connections, you must now config- ure it. You can do this using the serial interface (see 5.4 Connecting the programming interface), the network connection with an internet browser (see 7.4 Access using a browser) or Telnet (see 8... -
Page 9: Operation 7
Once you have been able to establish the connec- 1.1.3 IP Def. Gateway 1.6 Write Community tion to the CMC-TC Master II, the CMC-TC Master II 1.2 Trap Receiver Configuration 1.7 System Name start window appears. 1.2.1 IP Trap Receiver 1.8 System Contact... -
Page 10: Setting The Base Configuration
7.3.2 Configuring the trap receiver Main menu – 5 Read Community / 6 Write Com- To obtain messages and notifications, so-called trap munity messages, of the CMC-TC Master II, the IP address Parameter Explanation of the console on which the management software package (e.g. -
Page 11: Configuring System Name, Contact And Location
7.3.6 Configuring system name, Navigation contact and location Main menu – B Telnet Timeout Minutes A unique name, a contact address (e-mail) and a location can be entered for the CMC-TC Master II. Parameter Explanation Navigation B Telnet time- Set the Timeout function in out minutes minutes. -
Page 12: Access To The Entered Units
A security notification appears. You can confirm this by clicking the “Yes” button. Call your web browser as usual. Enter the IP ad- dress of the CMC-TC Master II in the address field and start building the page. 7.4.1 Login Fig. -
Page 13: Base Settings
Update connected devices: update the attached changes. To access the master again, Processing Units. you must login with the new IP address Firmware update: update the CMC-TC Master II. using your browser. 7.5.1 General setup Navigation Admin – General Setup – System Time Setup... - Page 14 To change the password, click in the field and press the Backspace key to clear the input. Enter the new e- mail address. System To quickly find the Master in the location data centre, you can enter the CMC-TC Master II...
-
Page 15: Create Users And Assign Rights
7.5.3 Entering the alarm recipient Name Enter the name of the user or The CMC-TC Master II can send alarms to receiver the user group. stations using SNMP. A maximum of four different receiver stations can be specified. In addition, a... -
Page 16: Settings For A Shutdown
Enable checkbox. down. Force closing If running programs should be of applications closed when a Shutdown com- Note! mand is issued, activate the To save the settings, you must click the checkbox. Change Configuration button. CMC-TC Master II... -
Page 17: Configuring Alarm Actions
7.5.5 Configuring alarm actions Webcams may be used. To setup the Webcams, You can configure various alarm actions on the proceed as follows. CMC-TC Master II. Click the “Create a new alarm action” link. Fig. 25 Alarm action configuration Configure alarm action Navigation Fig. -
Page 18: Creating Image Archives And Store Externally
"Show log file". Click the “Go Back” link to go back one step. Download log To store the log file, click file "Download log file". You will now be requested to store the text file. To do this, click “Save”. CMC-TC Master II... -
Page 19: Configure Overview Window
To load the update to the Master, proceed as 7.5.9 Configure overview window follows: You can upload any background image for the over- view window to the CMC-TC Master II. You can then position the Processing Units appropriately. and proceed as follows: Fig. 31 Update CMC-TC Master II... -
Page 20: Configuring Alarm Conditions
Sensor Select the sensor. State Select the status of the sensor. Remove To remove the condition, click “Remove”. Add combina- To link the condition with sev- tion eral sensors, click the "Add combination" button. CMC-TC Master II... -
Page 21: Configuring The Webcam Images
Alarm condition overview Show images View all images stored on the As Figure 35 shows, the new alarm condition is now CMC-TC Master II hard disk. shown in the overview. If you want to correct or Download Download the images not con-... -
Page 22: Setup For Logged In Processing Units
Configure the sensor units and sensors as Change values Click "Change values" to accept required. the settings. • After each setting change, click "Change val- ues" or "Change name". The Processing Unit also has an integrated beeper and an alarm relay. CMC-TC Master II... -
Page 23: Displaying The Status Of The Logged In Cmc-Tc Processing Units
You now see the logged in Processing Unit with its sensor units and connected sensors. • If you want to reconfigure the sensors, click the tool icon (4) to immediately display the Se- tup menu (see Section 7.8 CMC-TC Master II... -
Page 24: Overview Menu
Section 7.5.9 Configure overview window. You can directly display the status of the associated Processing Unit with a mouse-click (see Section 7.9 Displaying the status of the logged in CMC-TC Pro- cessing Units). CMC-TC Master II... -
Page 25: Administering Trap Messages
You have defined in Section 7.6, the priority of the 7.11 Administering trap messages individual messages. These messages will now be The CMC-TC Master II can receive traps from all displayed in the trap list (see Figure 41, step 5). logged in Processing Units. This requires that the CMC-TC Master II has been entered as trap re- ceiver with the Processing Unit. -
Page 26: Supported Rittal Components
Climate Unit 7320.230 Fan control system 7320.810 7858.488 Universal I/O Unit 7320.210 From software version 2.0, the CMC Master II also supports the following Rittal components: Components Model CMC-TC acoustic sensor 7320.640 PSM busbar with measurement 7856.016 7856.019 Rack extinguisher system DET-AC 7338.100... -
Page 27: Access Using Telnet 8
Access using Telnet 8 Access using Telnet Send SMS You can also configure the CMC-TC Master II using From software version 2.20 and with an additional Telnet. This requires that you are permitted to have GSM unit, the Master II is able to send an SMS. If... -
Page 28: Setting Up The Gsm Unit On The Master
Click on the "change" link in the "Notification" line card. (2). The SIM card will be blocked after three login attempts with incorrect PIN. Once the card is blocked, a mobile radio device must be used with the PUK to unblock the card. CMC-TC Master II... -
Page 29: Error Messages 10
Incorrect user- Check the username. name entered Incorrect pass- Check the password. word entered. No access authorisation using the browser Cause Rectification Incorrect user- Check the username. name entered Incorrect pass- Check the password. word entered CMC-TC Master II... -
Page 30: Maintenance And Cleaning
11 Maintenance and cleaning No access authorisation using Hyperterminal 11 Maintenance and cleaning Cause Rectification The Rittal CMC-TC Master II is a maintenance-free system. The housing does not need to be opened Incorrect user- Check the username. during the installation or during operation. -
Page 31: Storage And Disposal 12
175 mm 12.1.2 Disposal Weight without pack- approx. 0.6 kg Because the CMC-TC Master II consists primarily of the housing and PCB, the unit must be disposed of through the electronic waste recycling system when Potential equalisa- it is no longer required. -
Page 32: Technical Terms
15 Technical terms 15 Technical terms CMC-TC CMC-TC (Computer Multi Control – Top Concept) is a Rittal product used to monitor network enclosure components. GSM card A GSM card is a telephone card of a mobile tele- phone. Internet browser... - Page 33 Technical terms 15 Microsoft Windows is a registered trademark of Microsoft Corporation. Acrobat Reader is a registered trademark of Adobe Systems Incorporated. CMC-TC Master II...
- Page 34 Soluzioni per IT Soluciones TI Communication Systems Communication Systems Armoires outdoor Outdoor-behuizingen Communication Systems Soluzioni outdoor Sistemas de comunicación Rittal GmbH & Co. KG · Postfach 1662 · D-35726 Herborn Telefon +49(0)2772 505-0 · Telefax +49(0)2772 505-2319 · eMail: info@rittal.de ·...
Need help?
Do you have a question about the CMC-TC Master II and is the answer not in the manual?
Questions and answers