H3C CR16000-F Configuration Manual
Comware 7 oaa
Hide thumbs
Also See for CR16000-F:
- Hardware information and procedures (289 pages) ,
- Installation manual (206 pages) ,
- Command reference manual (55 pages)
Related Manuals for H3C CR16000-F
Summary of Contents for H3C CR16000-F
- Page 1 H3C CR16000-F Routers Comware 7 OAA Configuration Guide New H3C Technologies Co., Ltd. http://www.h3c.com.hk Software version: CR16000-CMW710-R7655P05 or later Document version: 6W100-20170825...
- Page 2 , H3CS, H3CIE, H3CNE, Aolynk, Care, , IRF, NetPilot, Netflow, SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New H3C Technologies Co., Ltd. All other trademarks that may be mentioned in this manual are the property of their respective owners Notice The information in this document is subject to change without notice.
- Page 3 Preface This configuration guide describes OAA fundamentals and configuration. It describes how to configure the H3C open application platform (OAP) module connected to your device to exchange information between your device and the OAP module. This preface includes the following topics about the documentation: •...
- Page 4 Convention Description example, the New User window opens; click OK. Multi-level menus are separated by angle brackets. For example, File > Create > > Folder. Symbols Convention Description An alert that calls attention to important information that if not understood or followed WARNING! can result in personal injury.
- Page 5 Obtaining documentation To access the most up-to-date H3C product documentation, go to the H3C website at http://www.h3c.com.hk To obtain information about installation, configuration, and maintenance, click http://www.h3c.com.hk/Technical_Documents...
-
Page 6: Table Of Contents
Contents Configuring the OAP module ······························································ 1 About OAP modules ··················································································································· 1 Logging in to an OAP module ······································································································· 1 Logging in through the console port on the OAP module ······························································ 1 Logging in through the management Ethernet port on the OAP module by using SSH ························ 1 ... -
Page 7: Configuring The Oap Module
OAP module. Assign an IP address to the management Ethernet port of the OAP module. M ake sure the management Ethernet port and the SSH client (an H3C device or a PC with SSH client software) can reach each other. -
Page 8: Logging In Through The Internal Ethernet Interface On The Oap Module By Using Ssh
After the SSH connection is successfully established, you are logged in to the operating system of the OAP module. Logging in through the internal Ethernet interface on the OAP module by using SSH When installed in the expansion slot of a device, an OAP module can exchange information with the device through internal interfaces, including a fast Ethernet interface. -
Page 9: Procedure
To avoid service data loss, close the operating system of an OAP module before resetting the module. Procedure Perform the following task in user view: Task Command In standalone mode: oap reboot slot slot-number Reset the OAP module. In IRF mode: oap reboot chassis chassis-number slot slot-number... -
Page 10: Configuring The Oap Manager
Configuring the OAP manager About OAP manager The Open Application Platform (OAP) is a hardware platform based on the Open Application Architecture (OAA). OAA allows products from different vendors to operate together to meet service requirements. OAP manager/client model OAP uses a manager/client model. •... -
Page 11: Oap Manager Timers
OAP manager timers The OAP manager uses the following timers: • Clock synchronization timer—Regularly triggers the OAP manager to send clock and time zone synchronization notifications to OAP clients. This mechanism keeps the clients' clocks synchronized with the manager's clock. •... -
Page 12: Shutting Down An Oap Client
Step Command Restart an OAP client. oap client reboot client-id Shutting down an OAP client This feature applies only to OAP clients on Linux. To shut down an OAP client: Step Command Enter system view. system-view Shut down an OAP client. oap client close client-id Display and maintenance commands for OAP manager... -
Page 13: Index
Index ACFP function OAP, OAP client, OAP manager configuration, 4, 5 OAP manager, application Application Control Forwarding Protocol. interface ACFP OAP module internal Ethernet interface login, logging in OAP module CLI login, OAP module, client OAP module CLI login, OAP client management, OAP module console port login, OAP client monitoring timer, 5, 5... - Page 14 OAP module configuration, logging in to OAP module (console port login), logging in to OAP module (internal Ethernet interface login), logging in to OAP module (management Ethernet OAP manager configuration, 4, 5 port login), OAP manager/client model, managing OAP client, OAP module CLI login, resetting OAP module, OAP module configuration,...
Need help?
Do you have a question about the CR16000-F and is the answer not in the manual?
Questions and answers