H3C CR16000-F Configuration Manual
Comware 7 oaa
Hide thumbs
Also See for CR16000-F:
- Hardware information and procedures (289 pages) ,
- Installation manual (206 pages) ,
- Command reference manual (55 pages)
Related Manuals for H3C CR16000-F
Summary of Contents for H3C CR16000-F
- Page 1 H3C CR16000-F Routers Comware 7 OAA Configuration Guide New H3C Technologies Co., Ltd. http://www.h3c.com Software version: CR16000-CMW710-R7951P01 or later Document version: 6W100-20191122...
- Page 2 The information in this document is subject to change without notice. All contents in this document, including statements, information, and recommendations, are believed to be accurate, but they are presented without warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions contained herein.
- Page 3 Preface This configuration guide describes OAA fundamentals and configuration. It describes how to configure the H3C open application platform (OAP) module connected to your device to exchange information between your device and the OAP module. This preface includes the following topics about the documentation: •...
- Page 4 Convention Description Folder. Symbols Convention Description An alert that calls attention to important information that if not understood or followed WARNING! can result in personal injury. An alert that calls attention to important information that if not understood or followed CAUTION: can result in data loss, data corruption, or damage to hardware or software.
- Page 5 It is normal that the port numbers, sample output, screenshots, and other information in the examples differ from what you have on your device. Documentation feedback You can e-mail your comments about product documentation to info@h3c.com. We appreciate your comments.
-
Page 6: Table Of Contents
Contents Configuring the OAP module ······························································ 1 About OAP modules ··················································································································· 1 Internal interfaces for OAP modules ······························································································· 1 Logging in to an OAP module ······································································································· 1 Logging in through the console port on the OAP module ······························································ 1 ... -
Page 7: Configuring The Oap Module
OAP provides an open interface for third-party vendors to develop and integrate value-added applications into H3C products. Internal interfaces for OAP modules An OAP module integrates a front card and a rear card. The front card provides value-added security services, such as firewall, intrusion prevention, and application control. -
Page 8: Logging In Through The Management Ethernet Port On The Oap Module By Using Ssh
OAP module. Assign an IP address to the management Ethernet port of the OAP module. M ake sure the management Ethernet port and the SSH client (an H3C device or a PC with SSH client software) can reach each other. -
Page 9: Resetting Oap Modules
• LSUM1ADECEA0. • LSUM1FWCEA0. • LSUM1IPSBEA0. • LSUM3FWCEA0. Procedure To log in to an OAP module from the CLI of the device, execute one of the following commands in user view: In standalone mode: oap connect slot slot-number In IRF mode: oap connect chassis chassis-number slot slot-number Resetting OAP modules About resetting OAP modules... - Page 10 Contents Configuring the OAP manager ···························································· 1 About OAP manager··················································································································· 1 About OAP ························································································································· 1 OAP manager/client model ···································································································· 1 OAP functions ···················································································································· 1 OAP manager timers ············································································································ 2 Configuring the OAP manager ······································································································ 2 ...
- Page 11 Configuring the OAP manager About OAP manager About OAP The Open Application Platform (OAP) is a physical platform that is based on the Open Application Architecture (OAA). OAP allows products from different vendors to operate together to meet service requirements. OAP manager/client model OAP uses a manager/client model.
- Page 12 • Display OAP client information. An OAP manager can manage up to 255 OAP clients. OAP manager timers The OAP manager uses the following timers: • Clock synchronization timer—Regularly triggers the OAP manager to send clock and time zone synchronization notifications to OAP clients. This mechanism keeps the clients' clocks synchronized with the manager's clock.
- Page 13 Shutting down an OAP client Restrictions and guidelines This feature applies only to OAP clients on Linux. Procedure Enter system view. system-view Shut down an OAP client. oap client close client-id Display and maintenance commands for OAP manager Execute display commands in any view. Task Command Display the summary registration information of OAP...
Need help?
Do you have a question about the CR16000-F and is the answer not in the manual?
Questions and answers