Related Manuals for Zenoah G2001
Summary of Contents for Zenoah G2001
- Page 1 G2001 115 59 98-38 (306) OWNER’S MANUAL CHAIN SAW G2001 Original Language GB-1...
-
Page 2: Table Of Contents
G2001 Contents SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into 1. Parts location ...........2 consideration to prevent possible serious bodily injury, and for 2. Specification ............3 this reason you are requested to read all such instructions care- fully and follow them without fail. -
Page 3: Specification
Displacement (cm ): ..........18.3 Power unit only (kg): ..........2.3 Fuel: ....Mixture (Gasoline 50: Two-cycle oil 1) (when using ZENOAH genuine oil) Cutting head: Fuel tank capacity (cm ) ........170 Sprocket (Teeth x Pitch): ........ 8T x 1/4 Chain oil: ........ -
Page 4: For Safe Operation
G2001 4. For safe operation WARNING This chainsaw has been especially designed for tree maintenance and should therefore only be used by trained operators when working on trees. When using this product for the first time, before beginning fingers encircling the chain saw actual work, learn to handling it from skilled worker. - Page 5 G2001 20. Operate the chain saw only in well handle, and the left hand on the front ventilated areas. Never start or run handle, when the engine is running. the engine inside a closed room or Use a firm grip with thumbs and fin- building.
- Page 6 G2001 WORKING WITH TREE SERVICE CHAIN-SAWS The saw should only be attached to the recommended attachment points on the harness. These may be at FROM A ROPE AND HARNESS This chapter sets out working practices to reduce the mid-point (front or rear) or at the sides. Where possible...
- Page 7 G2001 One-hand use of the chainsaw Operators should not use tree service chainsaws one- handed in place of unstable work positioning or in pref- erence to a handsaw when cutting small diameter wood at the branch tips. Tree service chainsaws should only be used one-handed where: • the operator cannot gain a work position enabling two-...
-
Page 8: Explanation Of Symbols On The Machine
G2001 5. Explanation of Symbols on the Machine For safe operation and maintenance, symbols are carved in relief on the machine. WARNING According to these indications, please be careful not to make any mistake. The port to refuel “MIX GASOLINE”... -
Page 9: Installing Guide Bar And Saw Chain
G2001 6. Installing Guide Bar and Saw Chain A standard saw unit package contains the items as illustrated. Plug wrench Power unit (Hexagon socket (S13/S16) + Bar protector Slotted driver) Guide bar Saw chain Screwdriver for carburetor adjustment (Slotted driver) -
Page 10: Fuel And Chain Oil
• The Zenoah engines are lubricated by oil specially formu- lated for air-cooled 2-cycle gasoline engine use. If Zenoah ■ FOR YOUR ENGINE LIFE, AVOID: oil is not available, use an anti-oxidant added quality oil 1. FUEL WITH NO OIL (RAW GASOLINE) – It will cause severe expressly labeled for air-cooled 2-cycle engine use (JASO FD damage to the internal engine parts very quickly. -
Page 11: Operating The Engine
G2001 8. Operating the Engine 6. When engine has ignited, first push in the choke knob WARNING to the first-stage position and then pull the starter It is very dangerous to run a chainsaw that mounts again to start the engine. -
Page 12: Sawing
G2001 1. Stop engine and screw L needle until it stops. WARNING Never force. Then set it back the initial number of turns as shown below. H needle is restricted within • When the brake operates, release the throttle lever to the number of turn as shown below. - Page 13 G2001 • This saw is equipped with a chain A log lying on the ground brake that will stop the chain in the event of kickback if operating prop- erly. You must check the chain brake operation before each usage by run-...
-
Page 14: Maintenance
G2001 10. Maintenance 3. Oil filter WARNING 1. With a wire hook, take out the oil filter from the feed- Before cleaning, the inspecting or repairing the unit, ing port. make sure that engine has stopped and is cool. Dis- connect the spark plug to prevent accidental starting. -
Page 15: Maintenance Of Saw Chain And Guide Bar
After each cutter has been filed, check the depth gauge and file it to the proper level as illustrated. WARNING: This saw is equipped with one of the following low kick- back bar/chain combinations: Zenoah Part Number Bar Size Guide Bar Saw Chain 2983-52111... -
Page 16: Troubleshooting Guide
G2001 12. Troubleshooting Guide Case 1. Starting failure Case 3. Oil does not come out Check oil for sub- ➡ WARNING Replace. standard quality. Make sure the icing prevention system is not working. ➡ Check fuel for water Replace with proper ➡... - Page 17 SPECIFIED BY THE COMPANY, OR OTHER CAUSES BEYOND THE COMPANY'S CONTROL. THE PURCHASER SHALL BEAR COSTS OF TRANS- PORTING THE UNIT TO AND FROM THE ZENOAH THIS WARRANTY DOES NOT COVER THOSE PARTS DEALER. REPLACED BY NORMAL WEAR OR HARMLESS CHANGES IN THEIR APPEARANCE.