Page 1
115 85 83-26 (1611) OWNER’S MANUAL CHAIN SAW G2200T Before using our products, please read this manual care- fully to understand the proper use of your unit. *01_G2200T__GB_CS5_五.indd 1 16/10/04 13:17...
Page 2
G2200T SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
G2200T 1. For safe operation WARNING This chainsaw has been especially designed for tree maintenance and should therefore only be used by trained operators when working on trees. National reg- both hands when the engine is run- ulation can restrict the use. Long or continuous expo- ning.
Page 5
G2200T 20. Operate the chain saw only in well element of surprise. Sudden surprise ventilated areas. Never start or run contributes to accidents. the engine inside a closed room or (2) Keep a good grip on the saw with building. Exhaust fumes contain dan- both hands, the right hand on the rear gerous carbon monoxide.
Page 6
G2200T c) ensure the saw is securely attached when it is being DISPOSAL • When you dispose of the machine, do not disas- sent up to the operator; semble the machine. d) ensure the saw it secured to the harness before it is • When you dispose of the machine, fuel, chain oil,...
Page 7
G2200T One-hand use of the chainsaw Operators should not use tree service chainsaws one- handed in place of unstable work positioning or in pref- erence to a handsaw when cutting small diameter wood at the branch tips. Tree service chainsaws should only be used one-handed where: • the operator cannot gain a work position enabling two-...
G2200T 2. Explanation of Symbols on the Machine For safe operation and maintenance, symbols are carved in relief on the machine. WARNING According to these indications, please be careful not to make any mistake. The port to refuel “MIX GASOLINE”...
G2200T 3. Installing Guide Bar and Saw Chain A standard saw unit package contains the items as illustrated. Plug wrench Power unit (Hexagon socket (S13/S16) + Guide bar cover Slotted driver) Guide bar Saw chain Screwdriver for carburetor adjustment (Slotted driver) Open the box and install the guide bar and the saw 5.
6. In the case of scrapping the used mixed oil container, scrap GASOLINE 50 : OIL 1 it only at an authorized repository site. <when using ZENOAH genuine oil> NOTE (JASO FD GRADE OIL or ISO-L-EGD GRADE) • Exhaust emission are controlled by the funda mental As for details of quality assurance, read the description in the engine parameters and components (eq., carburation,...
G2200T 5. Operating the Engine 6. When engine has started, turn the choke knob to WARNING the open positior and the pull the starter again to It is very dangerous to run a chainsaw that mounts the engine. broken parts or lacks any parts.
Page 12
G2200T 1. H and L needles are restricted within the number of ■ STOPPING THE ENGINE turn as shown below. 1. Release the throttle lever to allow the engine to idle for a few minutes. H needle : 1 1/2 ± 1/2 2.
G2200T 6. Sawing hand guard forward. The chain WARNING should stop immediately with the engine at full speed. If the chain • Before proceeding to your job, is slow to stop or does not stop, re a d t h e s e c t i o n “ F o r S a f e replace the brake band and Operation”.
Page 14
G2200T First check to which side the limb is bent. Then make A log lying on the ground the initial cut from the bent side and finish by sawing from the opposite side. WARNING Be alert to the springing back of a cut limb.
G2200T 7. Maintenance (b) If dirty, replace filter. Replace with new one if WARNING clogged with dirt. Before cleaning, the inspecting or repairing the unit, make sure that engine has stopped and is cool. Dis- WARNING connect the spark plug to prevent accidental starting.
G2200T 8. Maintenance of Saw Chain and Guide Bar ■ SAW CHAIN WARNING WARNING Be sure to round off the front edge to reduce the chance of kickback or tie-strap breakage. It is very important for smooth and safe operation to always keep the cutters sharp.
G2200T 9. Troubleshooting Guide Case 1. Starting failure Case 3. Oil does not come out Check oil for sub- WARNING Replace. standard quality. Make sure the icing prevention system is not working. Check fuel for water Replace with proper Check oil passage or substandard mix- Clean.
UNITS WHICH HAVE BEEN DAMAGED BY NEGLI- THE PURCHASER SHALL BEAR COSTS OF TRANS- GENCE OF INSTRUCTION LISTED IN THE OWNER/ PORTING THE UNIT TO AND FROM THE ZENOAH OPERATOR MANUAL FOR PROPER USE AND MAIN- DEALER. TENANCE OF THE UNITS ACCIDENT MISHANDLING,...
Page 19
G2200T To Dealer: Please complete the following form at time of sale. 經銷商銷售時請填寫下列表格。 Product Model: Equipment No.: ZENOAH 產品型號: 設備編號: G2200T Engine No.: 發動機編號: Date of Purchase: D / M / Y Use: 購買日期:日/月/年 用途: Private: 自用: Professional 專業用途: Rental 租賃:...
Page 20
PRINTED IN JAPAN *00_G2200T OM_Cover_CS5_三.indd 3 16/09/07 16:52...