Zenoah G3800AVS Manual
Zenoah G3800AVS Manual

Zenoah G3800AVS Manual

Zenoah chain saw owner/operator manual
Table of Contents

Advertisement

Quick Links

OWNER / OPERATOR MANUAL
MODE D'EMPLOI
MANUAL DE INSTRUCCIONES
WARNING
The engine exhaust from
this product contains
chemicals known to the
State of California to cause
cancer, birth defects or
other reproductive harm.
WARNING
Before using our
product, please read this
manual carefully to
understand the proper use
of your unit.
APPLICABLE SERIAL NUMBERS :
793480 and up
AVERTISSEMENT
Les échappements du
moteur de ce produit
contiennent des produits
chimiques connus par l'Etat
de Californie comme étant
responsables de cancers,
d'anomalies congénitales et
d'autres atteintes à
l'appareil reproducteur.
AVERTISSEMENT
Avant d'utiliser cette
produits, veuillez lire
attentivement ce manuel
afin de bien comprendre le
bon fonctionnement de cet
appareil.
NUMEROS DE SERIE APPLICABLES :
793480 et au-delà
CHAINSAW
TRONÇONEUSES
MOTOSIERRAS
G3800AVS
ADVERTENCIA
Los gases de escape del
motor de este producto
contienen sustancias
químicas conocidas por el
Estado de California como
causantes de cáncer,
malformaciones en recién
nacidos y otros problemas
de reproducción.
ADVERTENCIA
Antes de usar nuestros
productos, lea
detenidamente este manual
a fin de familiarizarse con el
uso correcto de este
aparato.
NÚMEROS DE SERIE APLICABLES:
793480 y superior
T2108-93112 (711)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the G3800AVS and is the answer not in the manual?

Questions and answers

Summary of Contents for Zenoah G3800AVS

  • Page 1 APPLICABLE SERIAL NUMBERS : 793480 and up CHAINSAW TRONÇONEUSES MOTOSIERRAS G3800AVS AVERTISSEMENT Les échappements du moteur de ce produit contiennent des produits chimiques connus par l’Etat de Californie comme étant responsables de cancers, d’anomalies congénitales et...
  • Page 2: Table Of Contents

    English SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
  • Page 3: La Seguridad Primero

    Français SECURITE Les instructions contenues dans les mises en garde de ce mode d’emploi portant le symbole concernent les points critiques qui doivent être pris en considération pour éviter les blessures corporelles graves, c’est pourquoi ces précautions doivent être rigoureusement suivies. ■...
  • Page 4: Parts Location

    5. Throttle interlock 6. Right handle 7. Throttle lever 8. Engine switch 9. Fuel tank 10. Oil tank 11. Left handle 12. Saw chain 13. Guide Bar (when using RedMax/ZENOAH genuine oil) Specifications are subject to change without notice. English...
  • Page 5: Emplacement Des Pieces

    10. Tanque de aceite 11. Asa izquierda 12. Cadena de la motosierre 13. Barraguia (Lors de l’utilisation de la véritable huile RedMax/ZENOAH) ) : ·························································································310 ) : ···································································································210 Les caractéristiques peuvent être modifiées sans préavis. (al utilizar el aceite auténtico de RedMax/ZENOAH) ): ···························································································310...
  • Page 6: Warning Labels On The Machine

    English 3. Warning labels on the machine (1) Read operator's instruction book before operating this machine. (2) Wear head, eye and ear protection. (3) Use the chain saw with two hands. (4) Warning! Danger of kickback. (5) Read, understand and follow all warnings.
  • Page 7: Etiquettes D'avertissement Sur La Machine

    Français 3. Etiquettes d’avertissement sur la machine (1) Lire le manuel avant d’utiliser cette machine. (2) Porter casque, lunettes de protection et protège-oreilles. (3) Utiliser la tronçonneuse en se servant des deux mains. (4) Avertissement ! Phénomène de rebond dangereux. (5) Lisez, cherchez à...
  • Page 8: Symbols On The Machine

    USE JASO FC OR ISO EGC GRADE 50:1 OIL. *1: The initial number will be changed every year of manufacturing. For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make any mistake. ZENOAH CO.,LTD.
  • Page 9: Symboles Utilises Sur La Machine

    Cylindree du moteur : 37cc Se fererer au manuel de l'utilisateur pour les specifications d'entretien et les reglages. FABRIQUE PAR: ZENOAH CO.,LTD. Utilise JASO FC ou ISO EGC 50:1 Huile. *1: Le nombre initial changera chaque année de la fabrication.
  • Page 10: For Safe Operation

    English 5. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. 2.
  • Page 11: Consignes De Securite

    Français 5. Consignes de securite 1. Ne jamais utiliser une tronçonneuse lorsqu’on est fatigué, malade, énervé, sous l’influence de médicaments entraînant vertige ou somnolence, ou encore sous I’influence de l’alcool ou de drogues. 2. Porter des chaussures de sécurité, des vêtements moulants, des lunettes de protection, un casque de sécurité...
  • Page 12 English 5. For safe operation 9. Never start cutting until you have a clear work area, secure footing, and a planned retreat path from the falling tree. 10. Always hold the chain saw firmly with both hands when the engine is running. Use a firm grip with thumb and fingers encircling the chain saw handles.
  • Page 13 Français 5. Consignes de securite 9. Avant de commencer à tronçonner, dégager le lieu de travail, prévoir une voie de retraite pour le moment où l’arbre va choir et bien se caler les pieds pour assurer sa posture. 10. Lorsque le moteur est en marche, tenir fermement la tronçonneuse à...
  • Page 14: Kickback Safety Precautions For Chain Saw Users

    English 5. For safe operation 16. Always shut off the engine before setting it down. 17. Use extreme caution when cutting small size brush and saplings because slender material may catch the saw chain and be whipped toward you or pull you off balance.
  • Page 15 Français 5. Consignes de securite 16. Toujours arrêter le moteur avant de poser la tronçonneuse. 17. Observer la plus grande prudence en coupant les broussailles. Une liane ou un arbrisseau se prenant dans la chaîne risquent de faire perdre l’équilibre ou de cingler le visage.
  • Page 16 English 5. For safe operation into your saw. As a chain saw user you should take several steps to keep cutting jobs free from accident or injury. (1) With a basic understanding of kickback you can reduce or eliminate the element of surprise. Sudden surprise contributes to accidents.
  • Page 17 Français 5. Consignes de securite • Les dispositifs de sécurité dont est équipée la tronçonneuse ne dispensent pas d’observer la plus grande prudence. Pour éviter tout accident ou blessure, observer scrupuleusement les consignes de sécurité ci-après lors de I’emploi de la tronçonneuse : (1) Une bonne compréhension du phénomène de rebond de la tronçonneuse permet de prévoir les situations où...
  • Page 18: Installing Guide Bar And Saw Chain

    English 6. Installing guide bar and saw chain ■ A standard saw unit package contains the items as illustrated. (F1) (1) Power unit (2) Guide bar (3) Saw chain (4) Plug wrench (5) Screwdriver for carburetor adjustment Open the box and install the guide bar and the saw chain on the power unit as follows: WARNING The saw chain has very sharp edges.
  • Page 19: Montage Du Guide-Chaîne Et De La Chaîne

    Français 6. Montage du guide-chaîne et de la chaîne ■ Contenu de I’emballage de la tronçonneuse. (F1) (1) Groupe moteur (2) Guide-chaîne (3) Chaîne (4) Clé pour obturateurs (5) Tournevis de réglage du carburateur Déballer et mettre en place le guide-chaîne et la chaîne sur le groupe moteur en procédant comme suite : AVERTISSEMENT...
  • Page 20 English 6. Installing guide bar and saw chain NOTE A new chain will expand its length in the beginning of use. Check and readjust the tension frequently as a loose chain can easily derail or cause rapid wear of itseif and the guide bar.
  • Page 21 Français 6. Montage du guide-chaîne et de la chaîne (3) Serrer (4) Vis du tendeur (5) Soulever REMARQUE Lorsqu’elle est neuve, Ia chaîne a tendance à s’allonger. Contrôler et régler fréquemment la tension de la chaîne. Si la chaîne est trop peu tendue, elle risque de sauter et s’use rapidement, ainsi que le guide-chaîne.
  • Page 22: Fuel And Chain Oil

    2-cycle engine use. (JASO FC GRADE OIL or ISO EGC GRADE) • Do not use BIA or TCW (2-stroke water-cooling type) mixed oil. ■ RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1 (when using RedMax/ZENOAH genuine oil) 50:1 MIXING CHART GASOLINE gal. 2-CYCLE OIL fl.oz...
  • Page 23: Carburant Et Huile De Chaîne

    (pour les moteurs 2 temps à refroidissement par eau). ■ RAPPORT DE MELANGE RECOMMANDE ESSENCE 50 : HUILE 1 (Lors de l’utilisation de la véritable huile RedMax/ZENOAH) TABLEAU DE MELANGE 50 :1 ESSENCE gal. HUILE 2 TEMPS once liquide ESSENCE...
  • Page 24: How To Mix Fuel

    English 7. Fuel and chain oil ■ HOW TO MIX FUEL IMPORTANT Agitate carefully. 1. Measure out the quantities of gasoline and oil to be mixed. 2. Put some of the gasoline into a clean, approved fuel container. 3. Pour in all of the oil and agitate well. 4.
  • Page 25 Français 7. Carburant et huile de chaîne participer ainsi à la protection de l’environnement et de votre santé. • De l’essence ou de l’huile de basse qualité risque d’endommager les joints, les conduites d’essence ou le réservoir d’essence du moteur. ■...
  • Page 26: Chain Oil

    English 7. Fuel and chain oil FOR YOUR ENGINE LIFE, AVOID; 1. FUEL WITH NO OIL(RAW GASOLINE) – It will cause severe damage to the internal engine parts very quickly. 2. GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication.
  • Page 27 Français 7. Carburant et huile de chaîne A EVITER POUR PROLONGER LA DUREE DE VIE DU MOTEUR; 1. ESSENCE SANS HUILE (ESSENCE PURE) – L’essence pure est capable d’endommager très rapidement les pièces du moteur. 2. ESSENCE-ALCOOL – Ce mélange risque de très rapidement détruire les pièces en caoutchouc et/ou en plastique et d’empêcher la lubrification du moteur.
  • Page 28: Operation

    English 8. Operation WARNING It is very dangerous to run a chainsaw that mounts broken parts or lacks any parts. Before starting engine, make sure that all the parts including bar and chain are installed properly. ■ STARTING THE ENGINE 1.
  • Page 29: Fonctionnement

    Français 8. Fonctionnement AVERTISSEMENT Il est dangereux d’utiliser une scie avec des pièces cassées ou manquantes. Avant de mettre le moteur en marche, toujours vérifier que toutes les pièces sont posées correctement, notamment la barre et la chaîne. ■ DémARRAGE DU MOTEUR 1.
  • Page 30: Checking The Oil Supply

    English 8. Operation 5. When engine has ignited, first push in the choke knob to the first-stage position and then pull the starter again to start the engine. 6. Allow the engine to warm up with the throttle lever pulled slightly. WARNING Keep clear of the saw chain as it will start rotatIng upon starting of engine.
  • Page 31 Français 8. Fonctionnement 5. Si le moteur démarre et cale, repousser le bouton de starter à la première position et tirer à nouveau la cordelette du lanceur pour remettre le moteur en marche. 6. Laisser le moteur se réchauffer en accélérant légèrement.
  • Page 32: Chain Brake

    English 8. Operation 1. H and L needles are restricted within the number of turn as shown below. H needle –1/4 L needle fixed 2. Start the engine and allow it to warm up in low speed for a few minutes. 3.
  • Page 33: Frein De La Chaîne

    Français 8. Fonctionnement 1. Le nombre de tour des pointeaux H et L est limité de la manière suivante. Pointeau H –1/4 Pointeau L fixé 2. Mettre le moteur en marche et le laisser se réchauffer à régime faible pendant quelques minutes.
  • Page 34: Stopping The Engine

    English 8. Operation immediately release your fingers from the throttle lever and stop the engine. ■ STOPPING THE ENGINE 1. Release the throttle lever to allow the engine to idle for a few minutes. 2. Set the switch to the “O” (STOP) position. (F17) (1) Switch Carburetor anti-freeze mechanism Operating the chain saws in temperatures of 0–5°C at...
  • Page 35: Arrêt Du Moteur

    Français 8. Fonctionnement entraîne des causes de pannes. Lorsque le frein s’applique accidentellement pendant le fonctionnement, dégager le doigt du papillon immédiatement pour arrêter le moteur. ■ ARRÊT DU MOTEUR 1. Relâcher la gâchette d’accélérateur et laisser le moteur tourner au ralenti pendant quelques minutes. 2.
  • Page 36 English 8. Operation ■ HOW TO SWITCH BETWEEN OPERATING MODES (F19) 1. Flip the engine switch to turn off the engine. 2. Remove the cover to the air filter, remove the air filter, and then remove the choke knob from the cylinder cover.
  • Page 37 Français 8. Fonctionnement ■ COMMENT CHANGER ENTRE LES MODES D’UTILISATION (F19) 1. Désenclencher le commutateur de moteur pour couper le moteur. 2. Déposer le capot au filtre à air, déposer le filtre à air, puis déposer le bouton de starter du cache- culbuteurs.
  • Page 38: Sawing

    English 9. Sawing WARNING • Before proceeding to your job, read "For Safe Operation" section It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. • Always follow the safety regulations. The chain saw must only be used for cutting wood.
  • Page 39: Travail À La Tronçonneuse

    Français 9. Travail à la tronçonneuse AVERTISSEMENT • Avant de commencer à travailler, Iire attentivement le chapitre “Pour la sécurité” au début de cette notice. Commencer à se familiariser avec le fonctionnement de la tronçonneuse en sciant quelques bûches dans de bonnes conditions de travail à...
  • Page 40 English 9. Sawing ■ FELLING A TREE (F22) 1. Decide the felling direction considering the wind, lean of the tree, location of heavy branches, ease of job after felling and other factors. 2. While clearing the area around the tree, arrange a good foothold and retreat path.
  • Page 41 Français 9. Travail à la tronçonneuse ■ Abattage d’un arbre (F22) 1. Déterminer le sens dans lequel I’arbre doit choir, compte tenu du vent, de l’inclinaison du tronc, de la disposition des branches les plus lourdes, de la commodité des travaux après abattage, etc. 2.
  • Page 42 English 9. Sawing A Log hanging off the ground (F24) In area A, saw up from the bottom one-third and finish by sawing down from the top. In area B, saw down from the top one-third and finish by sawing up from the bottom.
  • Page 43 Français 9. Travail à la tronçonneuse Tronc en surélévation (F24) Commencer par couper au tiers par en dessous dans la zone A et finir la coupe par-dessus. Dans la zone B, couper au tiers par-dessus et finir la coupe par en dessous.
  • Page 44: Maintenance

    English 10. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. WARNING Before cleaning, inspecting or repairing your unit, make sure that engine has stopped and is cool. Disconnect the spark plug to prevent accidental starting.
  • Page 45: Entretien

    Français 10. Entretien L’entretien, le remplacement ou la réparation du dispositif et des systèmes de lutte contre les émissions peuvent être effectués par toute société ou individu spécialisé dans la réparation des moteurs hors-route. AVERTISSEMENT Avant toute intervention de nettoyage, d’inspection ou de démontage, arrêter le moteur et attendre qu’il refroidisse.
  • Page 46: Periodical Service Points

    English 10. Maintenance ■ PERIODICAL SERVICE POINTS 1. Cylinder fins Dust clogging between the cylinder fins will cause overheating of the engine. Periodically check and clean the cylinder fins after removing the air cleaner and the cylinder cover. When installing the cylinder cover, make sure that switch wires and grommets are positioned correctly in place.
  • Page 47 Français 10. Entretien ■ ENTRETIEN PERIODIQUE 1. Ailettes de refroidissement du cylindre Si de la poussière reste entre les ailettes du cylindre, le moteur va chauffer. Vérifier périodiquement les ailettes du cylindre et les nettoyer en déposant le filtre à air et le couvre cylindre.
  • Page 48: Maintenance Of Saw Chain And Guide Bar

    English 11. Maintenance of Saw Chain and Guide Bar ■ Saw Chain WARNING It is very important for smooth and safe operation to keep the cutters always sharp. The cutters need to be sharpened when: • Sawdust becomes powder-like. • You need extra force to saw in. •...
  • Page 49: Entretien De La Chaîne Et Du Guide-Chaîne

    Français 11. Entretien de la chaîne et du guide-chaîne ■ Chaîne AVERTISSEMENT Pour la sécurité et le rendement dans le travail, les dents de la chaîne doivent toujours être bien affûtées. Les dents de chaîne doivent être affûtées lorsque : •...
  • Page 50 English 11. Maintenance of Saw Chain and Guide Bar Make sure every cutter has the same length and edge angles as illustrated. (F38) (4) Cutter length (5) Filing angle (6) Side plate angle (7) Top plate cutting angle ■ GUIDE BAR •...
  • Page 51 Français 11. Entretien de la chaîne et du guide-chaîne Vérifier que toutes les dents présentent les longueurs et angles de tranchant indiqués sur l’illustration. (F38) (4) Longueur de tranchant (5) Angle d’affûtage (6) Angle de tranchant latéral (7) Angle de tranchant supérieur ■...
  • Page 52: Troubleshooting Guide

    English 12. Troubleshooting Guide Case 1. Starting failure WARNING Make sure the icing prevention system is not working. Check fuel for water Replace with proper ➜ or substandard mix- fuel. ture. Remove and dry the Check for engine spark plug. ➜...
  • Page 53: Guide De Dépannage

    Français 12. Guide de dépannage Cas 1. Défaut de démarrage AVERTISSEMENT Veiller à ce que le système de prévention contre la congélation ne soit pas en fonctionnement. Vérifier s’il y a de l’eau Remplacer ➜ dans le combustible combustible approprié ou si le mélange n’est pas approprié.
  • Page 54: Storage

    English 13. Storage • Aged fuel is one of major causes of engine starting failure. Before storing the unit, empty the fuel tank and run the engine until it uses all the fuel left in the fuel line and the carburetor. Store the unit indoor taking necessary measures for rust prevention.
  • Page 55: Parts List

    15. Lista de piezas NOTE : 1. Use RedMax/ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. RedMax/ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified company.
  • Page 56 G3800AVS 15. Parts list Fig.1 POWER UNIT (S/N 793480 and up)
  • Page 57 848-870-A000 T2100-55610 2670-55410 T2100-71100 1650-43230 T2100-71300 T2100-71510 5500-72130 T2100-71220 2850-72110 1400-72121 2670-55410 72 3699-90032-10 T2108-15210 G3800AVS Q'TY DESCRIPTION NOTE /UNIT Clutch ass’y • Spring Plate Oil pump set • Oil pump • Worm Washer ø10.2xø15.5x1.0 Cover, pump Screw M4x14 Roter comp.
  • Page 58 G3800AVS 15. Parts list Fig.2 POWER UNIT (S/N 793480 and up)
  • Page 59 3317-75410 3330-75421 1850-75151 848-825-1911 T2108-75132 T2100-35110 2670-14320 T2108-81001 2850-82114 2867-82210 848-825-1911 T2102-35160 G3800AVS Q'TY DESCRIPTION NOTE /UNIT • Spring • Stopper plate • Spring • Washer ø5.2xø23x1.2 • Nut (B) R:M8x0.8 • Spring cover (Black) • Screw TP4x12 • Brake lever comp.
  • Page 60 Key# PART NUMBER /UNIT –––––––––– –––––––––– –––––––––– –––––––––– –––––––––– –––––––––– 2850-81190 2841-81450 2850-81430 2850-81350 2850-81461 G3800AVS Q'TY DESCRIPTION NOTE /UNIT • • SCREEN – • • VALVE, inlet – • • SPRING – • • PIN – • • LEVER –...
  • Page 61 2670-96240 Wrench (for clutch ASS’Y) 3330-97310 Gauge (for air gap) 2850-96410 Wrench (T20xT25xT27) 2670-96510 Guide (for break spring) T3195-91110 Q'TY NOTE Key# PART NUMBER /UNIT (OP) (OP) (OP) (OP) (OP) (OP) (OP) (OP) (OP) (OP) G3800AVS Q'TY DESCRIPTION NOTE /UNIT...
  • Page 62: Limited Warranty

    AMERICA, INC. AT (770)-381-5147. IMPORTANT: YOU WILL RECEIVE A WARRANTY REGISTRATION CARD AT TIME OF PURCHASE.PLEASE FILL OUT THE CARD AND SEND IT TO RedMax / ZENOAH AMERICA WITHIN SEVEN (7) DAYS. BE SURE TO KEEP A COPY FOR YOUR RECORDS.
  • Page 63: Garantie Limitée

    INC. au (770)-381-5147 Note importante: vous recevrez une carte d'enregistrement de garantie au moment de l'achat. Veuillez la remplir et l'adresser à RedMax / ZENOAH AMERICA sous sept (7) jours en prenant soin de conserver une copie pour vous. Garantie limitée ZENOAH AMERICA, INC.
  • Page 64: Garantía Limitada

    ZENOAH AMERICA, INC. LLAMANDO AL (770)-381-5147. IMPORTANTE: RECIBIRÁ UNA TARJETA DE REGISTRO DE GARANTÍA EN EL MOMENTO DE LA COMPRA. LLENE LA TARJETA Y ENVÍELA A RedMax / ZENOAH AMERICA DENTRO DE SIETE (7) DÍAS. ASEGÚRESE DE CONSERVAR UNA COPIA PARA SUS REGISTROS.

Table of Contents