Zenoah G4500 Owner's Manual
  1. Manuals
  2. Brands
  3. Zenoah Manuals
  4. Chainsaw
  5. G4500
  6. Owner's manual

Zenoah G4500 Owner's Manual

Hide thumbs Also See for G4500:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
G4500
115 40 09-38 (010)
G
G
B
B
OWNER'S MANUAL
CHAIN SAW
G4500
GB-1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the G4500 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Zenoah G4500

Summary of Contents for Zenoah G4500

  • Page 1 G4500 115 40 09-38 (010) OWNER’S MANUAL CHAIN SAW G4500 GB-1...

  • Page 2: Table Of Contents

    G4500 EXPLANATION OF SYMBOLS AND SAFETY WARNINGS Read operator's instruction Wear head, eye and ear book before operating this protection. machine. Use the chain saw Warning! Danger of with two hands. kickback. Read, understand and Never touch hot surface. follow all warnings.

  • Page 3: For Safe Operation

    G4500 1. For safe operation WARNING This chainsaw has been especially designed for tree maintenance and should therefore only be used by trained operators when working on trees. 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may 10.
  • Page 4 G4500 20. Operate the chain saw only in well handle, and the left hand on the front ventilated areas. Never start or run handle, when the engine is running. the engine inside a closed room or Use a firm grip with thumbs and fin-...

  • Page 5: Explanation Of Symbols On The Machine

    G4500 2. Explanation of Symbols on the Machine WARNING • For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make any mistake. The port to refuel “MIX GASOLINE”...

  • Page 6: Installing Guide Bar And Saw Chain

    G4500 3. Installing Guide Bar and Saw Chain A standard saw unit package contains the items as illustrated. Power unit Plug Screw File wrench driver round Grip Bar protector Guide bar Spike and mounting screws Saw chain Open the box and install the guide bar and the saw 5.

  • Page 7: Fuel And Chain Oil

    3. Fasten the fuel cap securely and wipe up any fuel spillage around the unit. WARNING • The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. 1. Select flat and bare ground for fueling.

  • Page 8: Operating The Engine

    G4500 5. Operating the Engine WARNING WARNING • It is very dangerous to run a chainsaw that mounts • Keep clear of the saw chain as it will start rotating broken parts or lacks any parts. upon starting of engine.
  • Page 9 G4500 1. Stop engine and screw in both H and L needles WARNING until they stop. Never force. Then set them back the initial number of turns as shown below. • Continuing to use the product in the anti­freeze H needle : 1 ±...

  • Page 10: Sawing

    G4500 6. Sawing seconds and pushing the front hand WARNING guard forward. The chain should stop • Before proceeding to your immediately with the engine at full job, read the section “For speed. If the chain is slow to stop or Safe Operation”.
  • Page 11 G4500 A log lying on the ground First check to which side the limb is bent. Then make the initial cut from the bent side and finish by sawing from the opposite side. WARNING • Be alert to the springing back of a cut limb.

  • Page 12: Maintenance

    G4500 7. Maintenance overheating of the engine. Periodically check and clean WARNING the cylinder fins in the repair specialty store. • Before cleaning, the inspecting or repairing the 2. Fuel filter unit, make sure that engine has stopped and is (a) Using a wire hook, take out the filter from the filler cool.

  • Page 13: Maintenance Of Saw Chain And Guide Bar

    G4500 8. Maintenance of Saw Chain and Guide Bar ■ Saw Chain WARNING WARNING • Be sure to round off the front edge to reduce the chance of kickback or tie­strap breakage. • It is very important for smooth and safe operation to always keep the cutters sharp.

  • Page 14: Troubleshooting Guide

    G4500 9. Troubleshooting Guide Case 1. Starting failure Case 3. Oil does not come out Check oil for sub- WARNING Replace. standard quality. • Make sure the icing prevention system is not work­ ing. Check oil passage Check fuel for water Clean.

  • Page 15: Specifications

    G4500 11. Specifications Power unit: Displacement (cm ): ...............................45.0 Fuel: ........................Mixture (Gasoline 50 : Two-cycle oil 1) (when using ZENOAH genuine oil) Fuel tank capacity (cm ): ............................550 Chain oil: ...........................Motor oil SAE# 10W-30 Oil tank capacity (cm ): ............................260 Carburetor: ............................Diaphragm type ignition system: ............................... Pointless Spark plug: .............................NGK BPMR7A...

  • Page 16: Limited Warranty

    WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF THE PURCHASER SHALL BEAR COSTS OF TRANS- INSTRUCTION LISTED IN THE OWNER/OPERATOR PORTING THE UNIT TO AND FROM THE ZENOAH MANUAL FOR PROPER USE AND MAINTENANCE OF DEALER. THE UNITS ACCIDENT MISHANDLING, ALTERATION,...

Table of Contents

Save PDF