MERLYN 6 Series Fitting Instructions

Fitting Instructions
I M P O R T A N T
Thank -you for choosing a MERLYN shower door.
Please familiarise yourself with these instructions before installing.
Do you have all the tools required?
Is the installation site compatible with the size of door supplied?
Are all the enclosure components present?
Is the installation kit complete?
<< M A J O R C O M P O N E N T S
sizes 800 & 900 in 1 box • size 1000 in 2 boxes
A B B
V 321 1 x 4
V 31 03 x 2
V 31 07 x 2
1
Ensure the shower tray is level in all directions and is
properly sealed to the w all. The wall must be tiled down to
the top edge of the tray. Do not angle out bottom tile.
5
Repeat steps 2 to 4 for top rail to nish frame.
R ail with short roller stops is the top rai l .
7
Place door frame into position on top of shower tray ensuring entry space is in the correct position. Align frame into position, drill through pro les at
similar position to wall xing screws and x to wall pro les with screws V4110, clips V2110 & snap-on caps V2109.
Quadrant 2 Door
DO N O T attempt to install the product unless you can tick ALL 4 boxes
adjacent as satisfactory.
The wall plugs supplied with the installation kit are for use in solid walls.
Holl ow or 'stud-partition' walls will require alternative xings. Please
consult a hardware supplier for the correct type.
It may also be necessary to consult your tiling supplier about the correct
method for drilling your tiles.
>>
V 6107 x 2
A
V11 06 x 2
C
V 4110 x 6
D
F I T T I N G I N S T R U C T I O N S - F O L L O W S T E P S I N S E Q U E N C E
2
Place xed panel gasket
V3211 onto bottom edge
of glass.
6
Place both wall pro les V1106 at 20mm from front edge of shower tray to outside edge of wall pro le, wall ange to inside, plumb, mark & drill
holes. Fix both the wall pro les into position with screws V4111, clips V2110 and caps V2109.
2nd wall pro le can be tted into door frame when lifting onto tray in situations where the enclosure is a tight t.
<< F I T T I N G K I T >>
V 2101L x 1
V 2101R x 1
V 6115 x 1
V 6113 x 6
V 2104 x 2
V 4111 x 14
V 2110 x 12 V 2109 x 12 V 6103 x 2
3
Loosen xed glass panel
clip.
2 0
m m
W A R N I N G
H E A V Y P R O D U C T, A S S I S T A N C E M AY B E R E Q U I R E D
U S E S A F E T Y E Y E W E A R W H E N D R I L L I N G
Any parts missing or damaged must be reported to your supplier
within 5 days of purchase. Please state size & colour of product and
part number as shown for the cor reponding size of door.
I N SP E C T DOO R B E F OR E F I T TIN G N O C LA IM S W I L L B E A C C EP T E D
A F T E R TH E DO O R HA S BE E N I N S TA L L E D
<< T O O L S Y O U W I L L N E E D
Power drill
Tape measure
#2 Philips screwdriver
Pencil/marker
Quality silicone sealant & applicator
Safety eyewear
Spirit-level with horizontal & vertical level indicators
4
Place xed glass panel into position on bottom r ail (with long
roller stops) & screw the frame together with screws V4111.
Tighten xed glass panel clip.
8
Fit handles V6107 to both doors.
>>
6mm masonry drill bit