Yaesu FT DX 9000 Series Technical Supplement page 59

AM-TXG Adjustment
Referring to table at
the right, tune the
MAIN Band (VFO-
A ) f r e q u e n c y t o
e a c h f r e q u e n c y
listed.
Connect the Dum-
my Load and Watt-
meter to the "ANT 1" Jack, then set the MAIN
Band (VFO-A) frequency to 1.850 MHz in the AM
mode.
Press and hold in the [ANT1], [ANT3], and [RX
ANT] keys, while turning the radio on, to enter
the alignment mode.
Rotate the Main Dial knob to select the Align-
ment Parameter "C28A."
Rotate the CLAR/VFO-B knob so that the VFO-B
frequency display shows "0."
Press the PTT switch without microphone input,
then rotate the CLAR/VFO-B knob for 70 W (D/
Contest) or 100 W (MP) on the Wattmeter.
Release the PTT switch.
Perform the same procedures for the Alignment
Menus "C28b" through "C37d," per the chart at
the right.
Press and hold in the [MNU] key for 2 seconds
to exit from the alignment mode.
1.8 MHz Band 1.850 MHz, AM
3.5 MHz Band 3.570 MHz, AM
7 MHz Band 7.100 MHz, AM
10 MHz Band 10.100 MHz, AM
14 MHz Band 14.200 MHz, AM
18 MHz Band 18.100 MHz, AM
21 MHz Band 21.200 MHz, AM
24.5 MHz Band 24.900 MHz, AM
28 MHz Band 28.700 MHz, AM
50 MHz Band 52.000 MHz, AM
A VFO-B F
LIGNMENT REQUENCY
P D
ARAMETER ISPLAY
C28A 0
C28b 0
C28c 0
C28d 0
C29A 0
C29b 0
C29c 0
C29d 0
C30A 0
C30b 0
C30c 0
C30d 0
C31A 0
C31b 0
C31c 0
C31d 0
C32A 0
C32b 0
C32c 0
C32d 0
C33A 0
C33b 0
C33c 0
C33d 0
C34A 0
C34b 0
C34c 0
C34d 0
C35A 0
C35b 0
C35c 0
C35d 0
C36A 0
C36b 0
C36c 0
C36d 0
C37A 0
C37b 0
C37c 0
C37d 0
Alignment
W
ATTMETER
D/C MP
ONTEST
70 W 100 W
20 W 50 W
10 W 20 W
5 W 10 W
70 W 100 W
20 W 50 W
10 W 20 W
5 W 10 W
70 W 100 W
20 W 50 W
10 W 20 W
5 W 10 W
70 W 100 W
20 W 50 W
10 W 20 W
5 W 10 W
70 W 100 W
20 W 50 W
10 W 20 W
5 W 10 W
70 W 100 W
20 W 50 W
10 W 20 W
5 W 10 W
70 W 100 W
20 W 50 W
10 W 20 W
5 W 10 W
70 W 100 W
20 W 50 W
10 W 20 W
5 W 10 W
70 W 100 W
20 W 50 W
10 W 20 W
5 W 10 W
70 W 100 W
20 W 50 W
10 W 20 W
5 W 10 W
ALIGNMENT-29