Advertisement
Installing the Camera
ATTENTION:
Test the camera prior to selecting a permanent
mounting location by temporarily connecting the
camera(s) and cables to the DVR.
To install the camera:
1. Use the included mounting template to mark and drill
holes for the included mounting screws.
NOTE:
Insert the included drywall anchors if installing into
drywall.
2. Connect the video and power cable as detailed in the
section 'Setting up the Camera'.
3. Attach the camera
base to the mouting
surface using the
included screws.
4. Set the position and angle of the camera using the
provided Allen key.
A
B
A) Loosen the screw on the
B) Loosen lower screw with
camera base with the Allen
the Allen key to adjust the
key to tighten / loosen the
camera's vertical position.
stand connection. Adjust the
camera's horizontal position.
C
C) Loosen the screws on either side of the
camera stand with the Allen key to rotate the
camera housing. Loosen the right-side to make
fine adjustments, or the left-side for broad
adjustments.
5. Remove the protective film from the camera lens.
Setting up the Camera
1. Connect one of the two BNC connectors on the camera to the
video cable. See "Camera Wiring" for details.
2. Connect a power source to the power terminal block. The
camera supports both 12V DC and 24V AC power supplies.
NOTE:
Make sure to follow correct polarity as marked on the
power connector. For AC power, connect multiple cameras using
consistent wiring polarity to prevent video rolling.
WARNING:
A REGULATED 12V DC or 24V AC power supply is REQUIRED for
use with this camera. Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.
Adjusting Zoom & Focus
Hold the joystick on the camera cable
/
out. The camera will focus itself automatically.
NOTE:
You can also adjust zoom and focus remotely if
the camera is connected to a FLIR MPX DVR using the
MPX video connector. See your MPX DVR's instruction
manual for details.
Camera Wiring
Analog
MPX
MPX
Analog
Connect to an MPX DVR for
Connect to an analog DVR for
1080p viewing / recording.
960H viewing / recording.
* Camera focus may be affected if the power connection is too
long. It is recommended not to extend the power connection
past 200ft (61m).
Extension Cable Options
The entire length of the cable run must be made using a
single extension cable between the camera and the DVR.
Specification
Maximum Length
RG59 20AWG Conductor 95% Braid
Up to 1000ft (300m)
CSA/UL or C(UL) Approved
RG6 20AWG Conductor 95% Braid
Up to 2000ft (600m)
CSA/UL or C(UL) Approved
Analog CCTV Balun
Up to 300ft (91m)
† Long cable runs over 1000ft (300m) may be affected by
electro-mechanical interference (EMI), which can increase the
amount of noise in the picture in some installations.
Camera Specifications
Image Sensor
Video Format
Effective Pixels
Resolution
Scan System
Sync System
S / N Ratio
Iris
AES Shutter Speed
to zoom in /
Min. Illumination
Video Output
Lens Focal Length /
Type
FOV (Horizontal)
Connect to a
Termination
12V DC or 24V AC
Power Consumption
power supply.*
Operating Temp. Range
Environmental Rating
Dimensions (W x H x D)
Weight (including stand)
IR Range / Qty.
Power Requirement
Camera Dimensions
†
†
3.9"
99mm
C237BD / C237BDP
C237BD1 / C237BD1P
1/2.8" 2.1MP CMOS
NTSC (C237BD)
NTSC (C237BD1)
PAL (C237BDP)
PAL (C237BD1P)
H: 1920 V: 1080
Digital: 1080p
Analog: 960H
Progressive
Internal
≥ 50dB (AGC Off)
AES
1/60 (1/50) ~ 1/60,000 sec.
0.1 LUX (IR Off)
0 LUX (IR LEDs On)
Digital: 1080p MPX HD-CVI
Analog: Composite 1.0Vpp @ 75ohm
2.8-12mm F1.4 /
6-22mm F1.4 /
Varifocal
Varifocal
MPX: 34-90°
MPX: 17-36°
960H: 32-84°
960H: 15-34°
BNC Type
12V DC: 700mA MAX with IR LED
24V AC: 585mA MAX with IR LED
–22° ~ 122°F / –30° ~ 60°C
IP66
3.9" x 3.5" x 10.6"
99mm x 89mm x 269mm
1.7lbs / 0.8kg
115ft / 35m; 42 IR LED's
12V DC / 24V AC
3.5"
89mm
10.6"
269mm
Advertisement
