1. Manuals
  2. Brands
  3. TriangleTube Manuals
  4. Boiler Supplies
  5. PGRKIT25
  6. Assembly instructions manual

TriangleTube PGRKIT25 Assembly Instructions Manual

Hmg delta classic replacement kit, electronic spark ignition
Hide thumbs
1
2
3
4
5
6

Advertisement

Table of Contents

HMG Delta CLASSIC Replacement Kit
Electronic Spark Ignition
Kit Part Numbers: PGRKIT25

Parts List

1- Series 1 Pilot Hood/Bracket Assembly
2- Series 2 Pilot Hood Assembly
3- Ground Rod
4- Ground Rod Sleeve
5- Ground Rod Sleeve Retainer Nut
6- Electrode
7- Pilot Orifice
8- 3/4" Spacer
9- Machine Screw
10- Nut
11- 3/8" Spacer
12- Lock Washer
13- L-Key Wrench
14- Retaining Screw
WARNING
Indicates a potentially hazardous situation
which, if ignored, can result in serious
injury or substantial property damage.
WARNING
Failure to follow instructions below can result
in severe personal injury or damage if ignored.
•
Instructions are for a qualified installer/ ser-
vice technician.
•
Read all instructions before proceeding.
•
Follow instructions in proper order.
1
2
10
11
13
8
12
NOTICE
Indicates special instructions on installa-
tion, operation or maintenance, which are
important to equipment but not related to
personal injury hazards.
WARNING
For your safety, turn off electrical power
supply at service panel before proceeding to
avoid possible electrical shock hazard.
Failure to do so can cause severe personal
injury or death.
1
4
3
9
6
14
5
7

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PGRKIT25 and is the answer not in the manual?

Questions and answers

Related Manuals for TriangleTube PGRKIT25

Summary of Contents for TriangleTube PGRKIT25

  • Page 1 HMG Delta CLASSIC Replacement Kit Electronic Spark Ignition Kit Part Numbers: PGRKIT25 Parts List 1- Series 1 Pilot Hood/Bracket Assembly 2- Series 2 Pilot Hood Assembly 3- Ground Rod 4- Ground Rod Sleeve 5- Ground Rod Sleeve Retainer Nut 6- Electrode 7- Pilot Orifice 8- 3/4”...
  • Page 2 HMG Delta CLASSIC Replacement Kit Electronic Spark Ignition Identifying Pilot Assembly Series If the pilot assembly is mounted on a horizontal If the pilot assembly is mounted on a vertical brack- bracket which is attached to the burner neck, refer et which is attached to the burner neck, refer to to Series 2 Conversion instructions.
  • Page 3 HMG Delta CLASSIC Replacement Kit Electronic Spark Ignition 2. Insert the pilot orifice into the pilot hood and WARNING tighten with a wrench. No thread sealant is nec- essary for the connection. If the burner plate insulation is damage or 3.
  • Page 4 HMG Delta CLASSIC Replacement Kit Electronic Spark Ignition Do not check for gas leaks with an open mounting nuts located to the left and right side flame. Use a gas detector or a bubble test. of the windbox. Failure to check for gas leaks can cause severe personal injury, death or severe prop- erty damage.
  • Page 5 HMG Delta CLASSIC Replacement Kit Electronic Spark Ignition 3. Insert the Ground Rod through the Ground Rod lation gasket. Failure to replace a damage insulation gasket can cause flue gas leakage Sleeve. Clip the retaining clip onto the Pilot for the burner assembly, resulting in severe Hood / Orifice.
  • Page 6 HMG Delta CLASSIC Replacement Kit Electronic Spark Ignition Fig. 2: Series 2 Pilot Assembly Fig. 1: Series 1 Pilot Assembly A. Pilot Orifice A. Pilot Hood / Bracket Assembly B. Pilot Hood Assembly (Series 2) B. Pilot Orifice C. Ground Rod C.

Table of Contents