Operation Manual - Sharp MD-E9000H Service Manual

Setting the Clock
This may be operated only with the remote control.
In this example, the clock is set for the 24-hour (0:00) display.
1
Press the CLOCK button and within 10 seconds, press the
MEMORY/ENTER button.
2
Press the or / button to select 24-hour or 12-hour
/
display and then press the MEMORY/ENTER button.
"0:00" The 24-hour display will appear.
(0:00 - 23:59)
"AM 0:00" The 12-hour display will appear.
(AM 0:00 - PM 11:59)
"AM 12:00" The 12-hour display will appear.
(AM 12:00 - PM 11:59)
Error Messages
When an error message is displayed, proceed as follows:
Error messages Meaning
BLANK MD Nothing is recorded.
(Neither music nor disc name
is recorded.)
Can't COPY You tried to record from a
copy prohibited CD.
Can't EDIT A track cannot be edited.
The disc is damaged.
Can't READ
TOC information cannot be
(
:Number or
read.
symbol)
MiniDisc not specified.
Can't REC Recording cannot be per-
formed correctly due to vibra-
tion or shock in the unit.
Can't WRITE The TOC information could
not be created properly due
to a mechanical shock or to
scratches on the disc.
The disc is out of recording
DISC FULL
space.
The CD cover is not working
Er-CD 20
properly.
A MiniDisc is not working
Er-MD
properly.
( :Number or
symbol)
You chose 21 or more tracks
EDIT OVER
for track editing.
The remaining time available
for recording is short.
MD NO DISC A MiniDisc has not been
loaded.
CD NO DISC
The MiniDisc data cannot be
read.
A CD has not been loaded.
The CD data cannot be read.
All manuals and user guides at all-guides.com

OPERATION MANUAL

To check the time:
Press the CLOCK button.
The time display will appear for about 10 seconds.
Note:
The "CLOCK" or time will flash at the push of the CLOCK button when the AC power
supply is restored after a power failure or unplugging the unit.
Readjust the clock by performing "Setting the Clock" from the beginning.
Remedy
Replace it with another disc.
Replace the CD.
Change the stop position of the
track and then try editing it.
Replace it with another disc.
Erase the disc and try record-
ing again.
Re-record or replace the
MiniDisc.
Set this unit to the stand-by
mode and try to write the
TOC again. (Remove any
source of shock or vibration
whilst writing.)
Replace the disc with another
recordable disc.
Set this unit to the stand-by
mode and turn the power on
again.
Set this unit to the stand-by
mode and turn the power on
again.
Decrease the number of
tracks.
Replace it with a disc that has
enough time to record.
Load a MiniDisc.
Reload the MiniDisc.
Load a CD.
Reload the CD.
– 7 –
3
Press the or / button to adjust the hour and then
/
press the MEMORY/ENTER button.
When the 12-hour display is selected, "AM" will change automatically to
"PM".
4
/
Press the / or button to adjust the minutes and
then press the MEMORY/ENTER button.
The hour will not advance even if minutes advance from "59" to "00".
The clock starts from "0" second. (Seconds are not displayed.)
Error messages Meaning
NAME FULL The number of characters for
the disc name or track name
exceeds 40.
NOT AUDIO The data recorded on this
disc is not audio data.
PLAYBACK MD You tried to record on a play-
back-only disc.
PROTECTED The disc is write protected.
TEMP OVER The temperature is too high.
TOC information recorded on
TOC FORM
the MD does not match the
( :Number or
MiniDisc specifications or it
symbol)
cannot be read.
There is no space left for re-
TOC FULL
cording track numbers.
There is no space left for re-
TOC FULL1
cording character informa-
tion.
The data contains an error.
? MD DISC
MiniDisc not specified.
MiniDisc is not working prop-
POWER?
erly.
Tuner is not working properly.
ER-TU
(
:Number or
symbol)
MD-E9000H
Remedy
Shorten the disc or track
name.
Select another track.
Replace the disc.
Replace it with another re-
cordable disc.
Move the write protection tab
back to its original position.
Set this unit to the stand-by
mode and wait for a whilst.
Replace it with another disc.
Erase the disc and try record-
ing again.
Replace it with another re-
cordable disc.
Replace it with another re-
cordable disc.
Erase the needless charac-
ters.
Replace it with another disc.
Set this unit to the stand-by
mode and turn the power on
again.
Set the unit to the stand-by
mode and turn the power on
again.