Operation Manual - Sharp SD-NX10 Service Manual

SD-NX10
Setting the Clock
In this example, the clock is set for 9:30 AM on August 15, 2001.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TIMER/DELETE button.
3
Within 10 seconds, press the REC LEVEL/CURSOR or button to
select the "TIME ADJUST".
4
Within 10 seconds, press the ENTER button.
5
Press the REC LEVEL/CURSOR
and then press the ENTER button.
6
Press the REC LEVEL/CURSOR
and then press the ENTER button.
Error Messages
When an error message is displayed, proceed as follows:
Error messages Meaning
BLANK MD Nothing is recorded. (Nei-
ther music nor disc name is
recorded.)
Can't COPY You tried to record from a
copy prohibited CD.
Can't EDIT A track cannot be edited.
Can't READ* The disc is damaged.
(*: Number or TOC information cannot be
symbol) read.
MiniDisc not specified.
Can't REC Recording cannot be per-
formed correctly due to vi-
bration or shock in the unit.
Can't T REC Timer recording is impossi-
ble or there is no available
space on the MD.
The disc is out of recording
space.
Can't WRITE The TOC information could
not be created properly due
to a mechanical shock or to
scratches on the disc.
CD NO DISC A CD has not been loaded.
The CD data cannot be
read.
DISC FULL The disc is out of recording
space.
EDIT OVER You chose 21 or more
tracks for track editing.
Er - MD ** A MiniDisc is not working
properly.
(**: Number or
symbol)

OPERATION MANUAL

or button to adjust the year,
or button to adjust the month,
Remedy
Replace it with another disc.
Replace the CD.
Change the stop position of
the track and then try editing it.
Replace it with another disc.
Erase the disc and try record-
ing again.
Re-record or replace the Mini-
Disc.
Replace it with another re-
cordable disc.
Set this unit to the stand-by
mode and try to write the TOC
again. (Remove any source of
shock or vibration while writ-
ing.)
Load a CD.
Reload the CD.
Replace the disc with another
recordable disc.
Decrease the number of
tracks.
Press the MD button.
Set this unit to the stand-by
mode and turn the power on
again.
7
Press the REC LEVEL/CURSOR
and then press the ENTER button.
8
Press the REC LEVEL/CURSOR
and then press the ENTER button.
The 12-hour display will appear.
"AM" will change to "PM" automatically.
9
Press the REC LEVEL/CURSOR or button to adjust the minutes,
and then press the ENTER button.
The hour will not advance even if minutes advance from "59" to "00".
The clock starts from "0" second. (Seconds are not displayed.) The time display
will disappear after a few seconds.
To confirm the time display:
[When the unit is in the stand-by mode]
Press the DISPLAY button on the remote control.
The time display will appear for about 5 seconds.
[When the power is on]
Press the TIMER/DELETE button.
Within 10 seconds, press the REC LEVEL/CURSOR
The time display will appear for about 10 seconds.
Note:
The clock setting will be cleared when the unit is unplugged or the power failure
occurs.
To reset the clock:
Perform "Setting the Clock" from the beginning.
Error messages Meaning
MD NO DISC A MiniDisc has not been
loaded.
The MiniDisc data cannot
be read.
NAME FULL The number of characters
for the disc name or track
name exceeds 40.
NOT AUDIO The data recorded on this
disc is not audio data.
PLAYBACK MD You tried to record on a
playback-only disc.
POWER ? A MiniDisc is not working
properly.
PROTECTED The disc is write protected.
TEMP OVER The temperature is too high.
TOC FORM ** TOC information recorded
on the MD does not match
(**: Number or
the MiniDisc specifications
symbol)
or it cannot be read.
TOC FULL There is no space left for re-
cording track numbers.
TOC FULL 1 There is no space left for re-
cording character informa-
tion.
? MD DISC The data contains an error.
MiniDisc not specified.
– 6 –
or button to adjust the date,
or button to adjust the hour,
AM 12:00 is 12 o'clock midnight.
PM 12:00 is 12 o'clock noon.
or button.
Remedy
Load a MiniDisc.
Reload the MiniDisc.
Shorten the disc or track
name.
Replace the disc.
Replace it with another re-
cordable disc.
Set this unit to the stand-by
mode and turn the power on
again.
Move the write protection tab
back to its original position.
Set this unit to the stand-by
mode and wait for a while.
Replace it with another disc.
Erase the disc and try record-
ing again.
Replace it with another re-
cordable disc.
Replace it with another re-
cordable disc.
Erase the needless charanc-
ters.
Press the MD button.
Replace it with another disc.