Bosch Rexroth AG Table of Contents Table of Contents Page About this documentation..............Overview on target groups and product phases........1 Purpose....................1 Availability....................2 Related documents................2 Customer feedback................2 Product identification and scope of delivery......... 2 Product identification................2 Scope of delivery...................
Page 4
CDI interface..................15 9.6.2 XVID and XSER marking............... 15 Mounting, demounting and electric installation........10.1 Housing dimensions................16 10.1.1 Rexroth design..................16 10.1.2 Special Rexroth design................ 10.1.3 Bosch design..................18 10.2 Installation notes................. 10.3 Mounting....................18 10.4 Mounting cut-out................. 10.5 Demounting..................
Page 5
Bosch Rexroth AG Table of Contents Page Maintenance..................14.1 Display....................14.2 Cleaning notes..................14.3 Scheduled maintenance tasks............. Ordering information................15.1 Accessories and spare parts..............31 15.2 Type code..................... 32 Disposal....................16.1 Take-Back..................... 32 16.2 Packaging..................... 33 Service and support................Index....................35...
Page 6
Bosch Rexroth AG DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P...
Bosch Rexroth AG About this documentation 1 About this documentation Editions of this documentation Edition Release Notes Date Edition 01 2013-10 First edition Edition 02 2014-03 Revision Edition 03 2018-05 Accessories supplemented, corrections Tab. 1-1: Change Record 1.1 Overview on target groups and product phases In the following illustration, the framed activities, product phases and target groups refer to the present documentation.
Please email your feedback on the documentations to Feed- back.Documentation@boschrexroth.de. Directly insert comments in the elec- tronic PDF document and send the PDF file to Bosch Rexroth. 2 Product identification and scope of delivery 2.1 Product identification The type plate is located on the rear side or at the side of the device.
Bosch Rexroth AG Using safety instructions Safety alert symbol Consequences and Signal word source of danger CAUTION Burns and chemical burns due to wrong battery treatment! Do not open the batteries and do not heat them over 80 °C. Avoiding danger Fig.
4 Intended use The Bosch Rexroth operator displays are passive operator and visualization ter- minals. They form a PC-based operator terminal when used with a Bosch Rexroth control cabinet PC. NOTICE Risk of damaging the device if not expressly sta-...
Bosch Rexroth AG Spare parts, accessories and wear parts Handling and assembly systems ● Packaging and food processing machines ● Printing and paper converting machines ● Machine tools ● Wood processing machines ● The operator displays may only be operated under the mounting and installation conditions, the position and the ambient conditions (temperature, degree of protection, humidity, EMC etc.) specified in this documentation.
Bosch Rexroth AG Spare parts, accessories and wear parts 5.4 Connecting cables for CDI interface Malfunctions caused by using inappropriate CDI cables. Use only cables listed in the following. Ordering code Part number Description RKB0008/000,5 (*******-*******-*******) R911171484 Length: 0.5 m...
Bosch Rexroth AG Ambient conditions Ordering code Part number Description RKB0019/003,0 (*******-*******-*******) R911171167 USB connecting cable, Length 3 m RKB0019/005,0 (*******-*******-*******) R911171168 USB connecting cable, Length 5 m Tab. 5-5: Connecting cables to the control cabinet PC 5.6 Wear parts Wear parts are not subject to any warranty.
Page 15
Bosch Rexroth AG Ambient conditions In operation Transport Storage Mechanical strength Max. vibration: Max. shock: Max. shock: Frequency range: 10… 15 g 11 ms 15 g 11 ms 150 Hz Acc. to EN 60068-2-27, Acc. to EN 60068-2-27, Excursion: 0.075 mm at...
The maximum permissible number and type of pixel errors of TFT displays de- pends on the manufacturer and is defined by the respective "incoming inspec- tion" of the vendor. This "incoming inspection" is provided by the Bosch Rexroth service if required.
Bosch Rexroth AG Standards 8 Standards The products have been developed according to the German edition of the standards published at the time of product engineering. 8.1 Standards used Standard Description EN 60 204-1 Safety of machinery - Electrical equipment of machines...
Bosch Rexroth AG Interfaces Standard Title Edition DIN EN 61000-6-4 Electromagnetic compatibility (EMC) September 2011 Part 6-4: Generic standards – Emission standard for indus- trial environments (EN 61000-6-4: 2007 + A1:2011) IEC 61000-6-2 Electromagnetic compatibility (EMC) 2006 + B1:2011 Part 6-2: Generic standards – Immunity for industrial envi- ronments (EN 61000-6-2:2005) Tab.
Bosch Rexroth AG Interfaces 9.2 Overview Name at the Connection type Connector type, inte- Mating connector or housing grated cable (from outside) ① S1 Refer to chapter 9.4 "S1 DIP switch" on page 14 ② XVID CDI interface, image RJ45 socket RJ45 plug ③...
Bosch Rexroth AG Interfaces Use a 24 V industrial power supply unit acc. to DIN EN 60742, classification VDE 0551, for example "VAP01.1H-W23-024-010-NN" (part number R911171065) for the voltage supply. 9.4 S1 DIP switch 9.4.1 Overview Fig. 9-3: S1 DIP switch at the connector panel of the operator display...
Interfaces Connect only USB devices that meet the USB2.0 specification. If any problems result when using USB3.0 devices, please contact the Bosch Rexroth Service. The cables of the connected USB devices have to comply with the USB2.0 specifications. If the total current of all USB ports exceeds 1 A, the power supply unit switches off the operator display.
Bosch Rexroth AG Mounting, demounting and electric installation 10 Mounting, demounting and electric installation 10.1 Housing dimensions 10.1.1 Rexroth design 422 mm (VDP 15.3), 554 mm (VDP 21.3) 346 mm (VDP 15.3), 478 mm (VDP 21.3) ① Visual range of the display Fig.
Bosch Rexroth AG Mounting, demounting and electric installation 10.1.2 Special Rexroth design 56,5 ① Visual range of the display Fig. 10-2: Housing dimensions of the operator display VDP 18.3 in millimeters, special Rexroth design 17/37 DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P...
Bosch Rexroth AG Mounting, demounting and electric installation 10.1.3 Bosch design 420 mm (VDP 15.3), 552 mm (VDP 21.3) 346 mm (VDP 15.3), 478 mm (VDP 21.3) ① Visual range of the display Fig. 10-3: Housing dimensions of the operator displays VDP 15.3 and VDP 21.3 in millime- ters, Bosch design 10.2 Installation notes...
Page 25
Bosch Rexroth AG Mounting, demounting and electric installation Loss of degree of protection IP 65! The housing, in which the operator display is installed, has to fulfill the following conditions: Free from impurities ● Sufficient mechanical strength and flatness ●...
Page 26
Bosch Rexroth AG Mounting, demounting and electric installation Fig. 10-5: Clamp fastening 4. Tighten the clamping screws. NOTICE Damage to the mechanics caused by wrong tightening torque Tighten the screws and nuts with the corresponding tightening torque according to the following table.
Bosch Rexroth AG Mounting, demounting and electric installation 10.4 Mounting cut-out 535 mm (VDP 21.3) 473 mm (VDP 18.3) 403 mm (VDP 15.3) ① Mounting cut-out Fig. 10-6: Mounting cut-out, specifications in millimeters 10.5 Demounting 1. Disconnect the operator display.
Bosch Rexroth AG Mounting, demounting and electric installation 10.6 Electric connection 10.6.1 Connecting operator display to control cabinet Connection diagram Violet XSER XSER Operator display Control cabinet PC XVID XVID Black Functional earth ground Fig. 10-8: Cabling operator display with control cabinet PC Connection 1.
Page 29
Bosch Rexroth AG Mounting, demounting and electric installation When wiring CDI cables with a diameter of 7.4 mm, observe the fol- lowing bending radii: Radius when bended once during wiring: 4 × cable diameter ● Minimum bending radius when moved permanently: 8 × cable di- ●...
Bosch Rexroth AG Mounting, demounting and electric installation 10.6.2 Connecting operator display to 24 V voltage supply Connection diagram 24 V voltage X1S1 Potential-free supply industrial power supply Operator display unit acc. to DIN EN 60742, classification VDE 0551 Fig. 10-9: Cabling operator display with control cabinet PC Connection 1.
Bosch Rexroth AG Mounting, demounting and electric installation 10.6.3 Overall connection scheme USB cable USB connection USB connection for USB2.0, max. 5 m Type A Type B XUSB1..6 XUSBIN, type B 230 V~ 24 V 24 V XVID XVID XSER XSER XUSB1...4...
Page 32
Bosch Rexroth AG Mounting, demounting and electric installation Shielding The shielding is an important component of the CDI cable. The shielding is used to shield the data wires in the cable against electrical interferences from the en- vironment. The shielding has to be connected to the potential equalization of the devices to shield the data wires.
Page 33
Bosch Rexroth AG Mounting, demounting and electric installation The CDI cable is sensitive to mechanical load where the jacket was removed. Ensure that the CDI cable shielding is not damaged when removing the cable jacket. Fig. 10-12: CDI cable with RJ45 plug Fig.
Bosch Rexroth AG Commissioning Fig. 10-16: CDI cable with shielding clamp More shielding clamps: ① Vendor: Ikotec ② Vendor: Phoenix Contact Fig. 10-17: Shielding clamps 11 Commissioning The product can be used directly, no configuration is required. 28/37 DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P...
Bosch Rexroth AG Error causes and troubleshooting 12 Device description 12.1 General information ① Status displays Fig. 12-1: Front view 12.2 Operating and error displays An LED for the operating display is located in the lower part of the front panel.
Bosch Rexroth AG Maintenance Errors Troubleshooting No image visible Connect the supply voltage and check the X1S1 connec- ● tion Connect the CDI cable correctly and check XVID and ● XSER Set the image output in the graphics driver to "VDP"...
Bosch Rexroth AG Ordering information A fading backlight causes a progressive deterioration display readability. Thus, a replacement is necessary. For further information, please contact the Bosch Rexroth Service. 14.2 Cleaning notes NOTICE Dissolving front glass sealing with solvent! Do not use solvents.
Bosch Rexroth AG Service and support Furthermore, the products returned for disposal must not contain any undue for- eign material or foreign components. Send the products "free domicile" to the following address: Bosch Rexroth AG Electric Drives and Controls Bürgermeister-Dr.-Nebel-Straße 2 D-97816 Lohr am Main, Germany 16.2 Packaging...
Page 40
Bosch Rexroth AG 34/37 DOK-SUPPL*-VDPXX.3MTBU-IT03-EN-P...
Bosch Rexroth AG Index Index 0 … 9 24 V DC voltage supply....13 Electric connection....... 22 24 V voltage supply....... 13 Electrical interferences....26 EMC interferences......25 EMC shielding clamp....27 Error causes........29 Accessories........6 Error displays........ 29 Ambient conditions......
Page 42
Bosch Rexroth AG Index Voltage supply (24 V DC)....13 Operating and error displays..29 Optical characteristic values..10 Overall connection scheme..25 Warnings......... 3 Wear parts........6, 8 Pixel errors........10 Potential equalization....25 XUSB interfaces......14 Power supply unit......2 Product identification.....