DVP-SE is small in size, and can be installed easily. Users do not have to install any batteries in DVP-SE series PLCs. The PLC programs and the latched data are stored in the high-speed flash memories.
Page 3
Model DVP12SE11R DVP12SE11T Item ESD (IEC 61131-2, IEC 61000-4-2): 8kV Air Discharge EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2kV, Digital I/O: 1kV, Noise immunity Analog & Communication I/O: 1kV RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m The diameter of grounding wire cannot be smaller than the wire Grounding diameter of terminals L and N (All DVP units should be grounded directly to the ground pole).
PLC when doing the programming). Safety Wiring Since DVP-SE is only compatible with DC power supply, Delta’s power supply modules (DVPPS01/DVPPS02) are the suitable power supplies for DVP-SE. We suggest you install the protection circuit at the power supply terminal to protect DVPPS01 or DVPPS02.
Page 5
AC power supply:100 ~ 240VAC, 50/60Hz Breaker Emergency stop: This button cuts off the system power supply when accidental emergency takes place. Power indicator AC power supply load Power supply circuit protection fuse (2A) DVPPS01/DVPPS02 ...
Page 6
4. Isolation circuit: The optical coupler is used to isolate signals between the circuit inside PLC and input modules. Relay (R) output circuit wiring DC power supply Emergency stop: Uses external switch Fuse: 5 to10A fuse at the shared terminal of output contacts to protect the output circuit ...
Page 7
N/C N/C N/C Note: The DVP-SE series PLC is equipped with the Auto MDI/MDIX function. It does not need any jumper wire when it connects to the network device. Setting the Ethernet The DVP-SE series PLC contains a built-in Ethernet communication port. Users have to set the network parameter before the PLC connects to other network devices.
Page 16
…………………………………………..………………… TÜRKÇE …………...……..……………………………………………… Delta’nın DVP-SE modelini seçtiğiniz için teşekkürler. DVP- SE PLC ürünü 12-nokta (8DI + 4DO) MPU, çeşitli komutlar ve 16K step program ile tüm DVP-S serisi genişleme modülleri (Maksimum 480 adet dijital I/O) ve yüksek hızlı ilave modüllerle (A/D, D/A dönüşüm ve sıcaklık ölçümü) ile bağlanabilir.
Page 17
Model DVP12SE11R DVP12SE11T Madde ESD (IEC 61131-2, IEC 61000-4-2): 8kV Hava Deşarj EFT (IEC 61131-2, IEC 61000-4-4): Güç Hattı: 2kV, Dijital I/O: 1kV, Ses Bağışıklığı Analog & Haberleşme I/O: 1kV RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m Topraklama kablosunun kesiti 24V - 0V terminalleri kabloları Topraklama kesitinden küçük olmamalıdır.
Page 18
(PLC programlanacağı zaman içindeki kalıcı röle ve register’lerin kullanımına dikkat ediniz). Güvenli Bağlantı DVP-SE ürünleri sadece DC voltaj ile beslenir. DELTA’nın güç kaynakları (DVPPS01/DVPPS02), DVP-SE PLC’lerin beslemesi için uygundur. DVPPS01 veya DVPPS02 ürünlerini korumak için power supply terminallerine koruyucu devre kurulması...
Page 19
2 çeşit DC giriş vardır, SINK veya SOURCE. İngilizce (English) bölümde Şekil 5’e [Figure 5] ve Şekil 6’ya [Figure 6] bakınız. Çıkış Bağlantısı 1. DVP-SE serisi ürünlerde 2 çeşit çıkış vardır. Röle ve Transistör (NPN/PNP). Çıkış terminal bağlantılarını yaparken ortak terminallerin kullanımına dikkat ediniz. (COM). 2.
Page 20
Ethernet RJ-45 haberleşme portuna bağlantı için lütfen sarmal çiftli CAT-5e kullanın. Tx+ N/C Tx- Rx- Rx+ N/C N/C N/C Not: DVP-SE serisi PLC Auto MDI/MDIX fonksiyonu ile donatılmıştır. Bir ağa bağlanırken cross bağlantıya ihtiyaç...