Installer Setting - Air Conditioner - LG PREMTB100 Owners & Installation Manual

INSTALLER SETTING
116
Installer setting – air conditioner
• You can set the product user functions.
• Some functions may not be displayed/operated in some product types.
Menu
It is the function to set the trial operation at the initial product installa-
Test run setting
tion.
Central control address
It is the function to set the central control address of the indoor unit
during the central controller connection.
Setting
It is the function to set the wind amount value corresponding to each
ESP setting
wind amount for easy installation.
It is the function to select the temperature sensor that will decide the
Temperature sensor setting
indoor temperature.
It is the function to control the wind amount stage according to the
Ceiling height setting
ceiling height for the ceiling type products.
The fixed pressure setting can be set only in the duct products.
Static pressure setting
It cannot be set in other products.
RMC master/slave setting It is the function to set group control or 2-remote controller control.
The operation master / slave selection function is to avoid other mode
operations, and it is the function to prevent the selection of the oppo-
Override master/slave setting
site mode of the indoor unit set as master by the indoor units set as
slaves.
Dry contact function is the function that can be used only when the
Dry contact mode setting
dry contact devices is separately purchased and installed.
It is the function to apply different fan speeds automatically for each
Fixed air volume
thermal control status.
It is possible to setup zone new type or old one of the product which
Zone Type Setting
is available to install the damper controller.
Zone Number is to set the number of installed zones. It's possible to
Zone Number Setting
control only in zone new type.
It is the function to set whether to use emergency heater control func-
Emergency Heater setting
tion and the usage environment.
Func. control during grp. It is the function to set common functions or some functions to be
Control setting controlled by the master indoor unit standard during the group control.
Option Kit – Plasma / Heater / It is the function to set whether to mount option unit (Plasma / Humid-
Humidification / Elevation grill ification / Heater / Ventilation / Elevation grill / Aux Heater / Refrigerant
/ Ventilation / Refrigerant leak- leakage detection sensor) when it is additionally installed or removed
age detection sensor after the mass production.
Expand of Temperature Range This function is used for select setting temperature range option.
Indoor unit address verifica- This function allows you to check the address of the indoor unit desig-
tion nated by the outdoor unit.
This is the function that static pressure of the product is divided in 11
Static pressure step setting
steps for setting.
Description
Menu
It is a function that sets the minimum running time of outdoor unit
Guard timer cycle mode when switching from cooling mode to heating mode and
vice versa during Auto Operation mode.
Fan speed in Cooling thermal It is a function that sets the indoor unit fan movement, in cooling
off mode, when thermal is off.
It is the function to set the heater usage to have higher priority over
Primary heater setting
the outdoor unit cycle during the indoor unit heating operation.
Air conditioner Fan operation It is the function to set whether to operate the air conditioner fan dur-
interlocked with ventilation ing the interface operation of the air conditioner and the ventilation
setting product.
It is a function that sets whether to restore the indoor unit operation
Indoor unit Auto-Start
by resuming the previous power-on state or as power-off state in the
setting
power failure compensation.
Occupancy duration time It is the function to set the occupied decision maintaining time among
setting the occupied sensor values.
It is the function to set whether to install (use) Dry Contact.
CN_CC setting (It is not a function for Dry Contact installation, but it is a function to
set the usage of the indoor unit's CN_CC port.)
It is the function to set the indoor unit's Dry Contact Port to control ex-
ternal input and output according to DI/DO set by the customer. (It is
CN_EXT setting
the function to decide the usage of the contact point port (CN_EXT)
mounted in the indoor unit PCB.)
ODU function master setting It is the function to set the outdoor unit's function Master / Slave.
It is the function to set the indoor unit's continued Fan function usage.
Fan continuous operation It is the function to maximize the cooling/heating efficiency by the out-
setting door unit operating the indoor unit fan operation longer than the previ-
ous operation method.
It is the function to set the main agent of the low noise mode control.
Low noise mode priority
(It is the function to set only one of the outdoor unit / remote con-
setting
troller can control the low noise operation.)
Human detection sensor set- It is the function to set whether to install human detection sensor and
ting operation standard value.
Humidity sensing position It is the function to set the location to detect humidity.
ODU cycle priority This function can select standby mode or priority cooling.
Outdoor temp. for heating This function can select outdoor temperature values for use reference
stages point of heater and heating mode operation.
Estimated energy display This function can set to display energy data which ODU estimated.
CN_PTC setting This is a function to set PTC Port of indoor unit.
It is the function to initialize (0000) the password when you forgot the
Password initialization
password set in the remote controller.
This function automatically sets the rotation speed of the fans
Auto ESP
corresponding to each step of rated airflow for easy installation.
Dust step color setting This function is to set the dust step color.
INSTALLER SETTING
117
Description