DoorKing 9150-084 Installation & Owner's Manual page 26

3.2 Continued
Switch Function
Exit Loop Port
Output
1
Full Open Input
Reverses Gate
2
Stops Gate
Partial Open
3
(14 Ft)
Built-in
Solenoid
4
Lock
Operator Model
5
Select
Quick-Close
6
Timer Override
Gate Close
7 and 8 Back-Off
Position
SW 2 Switch 1 Switch 1 Determines if the output of the loop detector (DoorKing loop detectors only) plugged into the EXIT loop
port will be sent directly to the microprocessor to open (or reverse a closing gate) the gate, or if the output is directed to Main
Terminal #10 where it can be connected to other input terminals.
SW 2 Switch 2 Determines if an input to terminal #6 (Photo Sensors) AND/OR reverse loops will reverse OR stop a CLOSING gate.
A tailgating vehicle can activate terminal #6 (Photo sensors) and/or reverse loops while the gate is in the closing cycle from the
previous vehicle's authorized entry:
If switch 2 is turned OFF (Reverse), the closing gate that gets activated by a tailgating vehicle will reverse back to the open
position, possibly allowing the tailgating vehicle unauthorized entry while the gate is reversing back to the open position.
If switch 2 is turned ON (Stop), the closing gate that gets activated by a tailgating vehicle will stop, partially or completely
blocking the pathway, NOT allowing the tailgating vehicle to enter without proper authorization. The gate will not move until all
sensors are clear, usually forcing the tailgating vehicle that activated the sensors to back away from the gate. The gate will then
continue until closed, helping prevent the tailgating vehicle from unauthorized entry.
Switch must be in the OFF position. Inputs connected to terminal #5 will open and reverse the gate only 14 Ft.
SW 2 Switch 3
SW 2 Switch 4 This switch determines the operation of the built-in solenoid lock. The OFF setting is the factory setup. Caution:
Do not set this switch to ON unless the 2600-865 fail-secure manual release kit has been installed in the operator.
Changing this switch to the ON setting without installing the lock kit will damage the operator. See pages 35 and 36 for more
information about Fail-Safe vs. Fail-Secure release systems.
SW 2 Switch 6 Turning the quick-close feature on will cause the auto-close timer to close the gate after 1 second, regardless of
the setting of the auto-close timer potentiometer. This will also cause an opening gate to stop and reverse when the reverse
loops and/or photo sensors are cleared. This feature, along with turning SW 2, switch 2 ON above, is useful to help prevent
tailgating vehicles from unauthorized entry.
These work in conjunction with each other and determine if the operator will stop the gate at the full close
SW 2 Switches 7-8
position, or if the gate should stop 1, 2 or 3 inches short of the full close position. Needed only when using a reversing edge
entrapment protection device on the closing edge of the gate with an end post as the physical stop.
22
SW 2 (Right 8 Switches)
Setting
OFF
Switches logic level output of EXIT loop port to main terminal #10.
Normal Setting. Plug-in exit loop detector will fully open gate (Single operator).
ON
OFF Normal Setting. Input to terminal #6 and/or reverse loops will reverse gate
during close cycle.
Input to terminal #6 and/or reverse loops will stop gate during close cycle – gate
ON
will continue to close after input to terminal #6 and/or reverse loops are cleared
(Helps prevent tailgating vehicles from unauthorized entry).
Normal Setting. Switch must be OFF for terminal #5 input to open gate 14 Ft.
OFF
DO NOT use ON setting. NOT associated with partial open feature for the 9150.
ON
Normal Setting. Fail-safe logic. Lock engages only if attempt is made to force gate
OFF
open (Factory setup).
Fail-secure logic. Lock engages after each gate cycle (2600-865 Lock kit required).
ON
Normal Setting. Switch must be OFF for Model 9150.
OFF
DO NOT use ON setting for Model 9150.
ON
Normal Setting. Timer will function normally.
OFF
Opening gate will stop and begin to close as soon as all reversing inputs (Reverse
ON
loops, photo sensors) are cleared regardless of the distance the gate has opened.
Normal Setting. Gate fully closes.
7-OFF 8-OFF
Gate stops short 1" from full close position. Used for a reversing edge device.
7-OFF 8-ON
Gate stops short 2" from full close position. Used for a reversing edge device.
7-ON 8-OFF
Gate stops short 3" from full close position. Used for a reversing edge device.
7-ON 8-ON
Description
9150-065-M-5-18