Canon imageRUNNER 2530 Service Manual Digest page 25

Ecode Detail Item
Code
E532 0002 Title
Description
Remedy
E540 0001 Title
Description
Remedy
E540 0005 Title
Description
Remedy
E542 0001
Title
3
Description
Remedy
E542 0005
Title
Description
Remedy
E567 0001 Title
Description
Remedy
E567 0002 Title
Description
Remedy
3-6
Description
STP Move Motor (M1) error
The stapler does not return to the stapler move home position
when the STP Move Motor (M1) has been driven for 2.8 sec.
1.Replace the Stapler Move HP Sensor (S10).
2.Check the wiring between the Finisher Controller PCB and
the STP Move Motor.
3.Check the stapler shift base.
4.Replace the STP Move Motor (M1).
5.Replace the Finisher Controller PCB (PCB1).
Tray Lift Motor (M11) time out error
The stack tray does not move within a specified time period.
1.Replace the Tray Lift Motor (M11).
2.Replace the Finisher Controller PCB (PCB1).
Tray Lift Motor (M11) closing detect switch error
The FG input cannot be detected when the Tray Lift Motor
(M11) has been driven for 0.1 second.
1.Replace the Stack Tray Clock Sensor (S13).
2.Replace the Tray Lift Motor (M11).
3.Replace the Finisher Controller PCB (PCB1).
Additional Tray Lift Motor (M12) time out error
The stack tray does not move within a specified time period.
1.Replace the Additional Tray Lift Motor (M12).
2.Replace the Finisher Controller PCB (PCB1).
Additional Tray Lift Motor (M12) closing detect switch error
The FG input cannot be detected when the Additional Tray
Lift Motor (M12) has been driven for 0.1 second.
1.Replace the Additional Tray Clock Sensor (S23).
2.Replace the Additional Tray Lift Motor (M12).
3.Replace the Finisher Controller PCB (PCB1).
Shift Roller Release Motor (M5) error
The shift roller does not leave the shift roller release home
position when the Shift Roller Release Motor (M5) has been
driven for 0.1 sec.
1.Replace the Shift Roller Release Sensor (S3).
2.Replace the Shift Roller Release Motor (M5).
3.Replace the Finisher Controller PCB (PCB1).
Shift Roller Release Motor (M5) error
The shift roller does not return to the shift roller release home
position when the Shift Roller Release Motor (M5) has been
driven for 0.06 sec.
1.Replace the Shift Roller Release Sensor (S3).
2.Replace the Shift Roller Release Motor (M5).
3.Replace the Finisher Controller PCB (PCB1).
Ecode Detail Item
Code
E571 0001 Title Gripper Open/Close Motor (M7) error
Description The gripper unit does not leave the gripper unit home position
when the Gripper Open/Close Motor (M7) has been driven for
0.25 seconds.
Remedy 1.Replace the Grip Arm Sensor (S13).
2.Replace the Gripper Open/Close Motor (M7).
3.Replace the Finisher Controller PCB (PCB1).
E571 0002 Title Gripper Open/Close Motor (M7) error
Description The gripper unit does not return to the gripper unit home
position when the Gripper Open/Close Motor (M7) has been
driven for 0.15 seconds.
Remedy 1.Replace the Grip Arm Sensor (S13).
2.Replace the Gripper Open/Close Motor (M7).
3.Replace the Finisher Controller PCB (PCB1).
E575 0001 Title Gripper Unit Move Motor (M2) error
Description The gripper unit does not leave the gripper unit home position
when the Gripper Unit Move Motor (M2) has been driven for
3.8 seconds.
Remedy 1.Replace the Gripper Unit HP Sensor (S7).
2.Replace the Gripper Unit Move Motor (M2).
3.Replace the Finisher Controller PCB (PCB1).
E575 0002 Title Gripper Unit Move Motor (M2) error
Description The gripper unit does not return to the gripper unit home
position when the Gripper Unit Move Motor (M2) has been
driven for 0.1 seconds.
Remedy 1.Replace the Gripper Unit HP Sensor (S7).
2.Replace the Gripper Unit Move Motor (M2).
3.Replace the Finisher Controller PCB (PCB1).
E602 0001 Title The built-in SD card is not detected
Description -
Remedy -
E602 1105 Title Access to the built-in SD card failed
Description -
Remedy -
E711 0001 Title Error in UFDI communication
Description The communication system error (such as reception timeout
or checksum error) occurred.
Remedy 1.Check and Replace the cable.
2.Replace the DC Controller PCB (PCB4).
3.Replace the Finisher Controller PCB.
E713 0000 Title Erroneous communication with finisher
Description The communication does not restart by the error retry after
the communication failure with the finisher.
Remedy 1.Check the cable.
2.Replace the DC Controller PCB (PCB4).
3.Replace the Finisher Controller PCB.
Description