VIBRATION INFORMATION Vibration total values (triax vector sum) determined according to EN 60745: Vibration emission value a = 5,480m/s Cutting wood Uncertainty K= 1.5m/s² Vibration emission value a = 4,628m/s Cutting metal Uncertainty K= 1.5m/s² Vibration emission value a = 6.13m/s Cutting tile Uncertainty K = 1.5m/s²...
Page 11
ACCESSORIES WX523 WX523.9 TCT 24T Blade HSS 44T Blade Diamond Disc Parallel Guide Vacuum Adaptor Hex Key 20V 2.0 Ah Li-Ion battery WA3551.1 1hr charger(WA3860) We recommend that you purchase your accessories from the same store that sold you the tool. Use good quality accessories marked with a well-known brand name.
GENERAL POWER TOOL suitable for outdoor use reduces the risk of electric shock. SAFETY WARNINGS 6) If operating a power tool in a damp location is unavoidable, use a residual WARNING: Read all safety warnings current device (RCD) protected and all instructions. Failure to follow supply.
Page 13
4. POWER TOOL USE AND CARE used with another battery pack. 2) Use power tools only with specifically 1) Do not force the power tool. Use designated battery packs. Use of any the correct power tool for your application. The correct power tool will other battery packs may create a risk of injury and fire.
SAFETY WARNINGS FOR FURTHER SAFETY ALL SAWS INSTRUCTIONS FOR ALL SAWS DANGER: Keep hands away from cutting area and the blade. If both KICKBACK CAUSES AND RELATED hands are holding the saw, they cannot be WARNINGS cut by the blade. - Kickback is a sudden reaction to a pinched, b) Do not reach underneath the bound or misaligned saw blade, causing an...
ADDITIONAL SAFETY Large panels tend to sag under their own weight. Supports must be placed under RULES FOR YOUR the panel on both sides, near the line of cut CIRCULAR SAW and near the edge of the panel. e) Do not use dull or damaged blades. 1) Always wear a dust mask, hearing Unsharpened or improperly set blades protection and eye protection.
Page 16
smaller tool and may burst. operator an electric shock. g) The outside diameter and the m) Never lay the power tool down until thickness of your accessory must the accessory has come to a complete be within the capacity rating of your stop.
b) Never place your hand near the “pocket cut” into existing walls or rotating accessory. Accessory may other blind areas. The protruding wheel kickback over your hand. may cut gas or water pipes, electrical C) Do not position your body in line with wiring or objects that can cause kickback.
Page 18
FOR BATTERY PACK n) Recharge only with the charger a) Do not dismantle, open or shred cells specified by WORX. Do not use any or battery pack. charger other than that specifically b) Do not short-circuit a battery pack. Do provided for use with the equipment.
Page 19
SYMBOLS To reduce the risk of injury, user Wear protective gloves must read instruction manual Wood Warning Wear ear protection Metal Aluminium Wear eye protection Plastic Wear dust mask Tile Do not stare into beam Incorrect Laser radiation Waste electrical products must not Correct be disposed of with household waste.
Page 20
OPERATING INSTRUCTIONS Do not expose to rain or water NOTE: Before using the tool, read the instruction book carefully. INTENDED USE: Do not burn The tool is intended for ripping and cross- cutting wood and other materials in straight cutting lines, while resting firmly on the work Positive terminal piece.
WORKING HINTS FOR YOUR ENVIRONMENTAL TOOL PROTECTION If your power tool becomes too hot, please Waste electrical products must not be run your circular saw no load for 2-3 minutes disposed of with household waste. to cool the motor. Avoid prolonged usage at Please recycle where facilities exist.
TROUBLE SHOOTING Symptom Possible Causes Possible Solution Battery park not plugged Check to make sure battery park is connected well into a working Tool will not start when Battery park is powered off. outlet operating the on/off switch. Carbon brush has worn Charging the battery.
DECLARATION OF CONFORMITY Positec Power Tools (Europe) Ltd, PO Box 6242 Newbury RG14 9LT UK Declare that the product, Description Battery-powered circular saw Type WX523 WX523.9 (5-designation of machinery, representative of Saw) Function Cutting various materials with a rotating toothed blade Complies with the following Directives, 2006/42/EC 2011/65/EU...
Need help?
Do you have a question about the WorxSaw WX523 and is the answer not in the manual?
Questions and answers