VAT 284 Series Installation, Operating,  & Maintenance Instructions

VAT 284 Series Installation, Operating, & Maintenance Instructions

Uhv angle valve

Advertisement

Quick Links

UHV Angle valve
● with manual actuator,
This manual is valid for the valve ordering number(s):
284..
285..
The fabrication number is indicated on each product as per the label
below (or similar):
made in Switzerland
Fabrication No.:
patented
284. . – . . . . – . . . . / . . . .
A – . . . . . .
Explanation of symbols:
Read declaration carefully before you start any other
action!
Attention!
Product is in conformity with EC guidelines,
if applicable!
Disconnect electrical power and compressed air
lines. Do not touch parts under voltage!
Read these «Installation, Operating & Maintenance Instructions» and the enclosed «General
Safety Instructions» carefully before you start any other action!
VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com
Installation, Operating & Maintenance Instructions
Series 284, DN 16, 25, 40, 63
Series 285, DN 16, 25, 40, 63
. .
Fabrication number
(ID 5/8", 1", 1½", 2½")
(ID 5/8", 1", 1½", 2½")
Keep body parts and objects away from the valve
opening!
Hot surfaces; do not touch!
Loaded springs and/or air cushions are potential
hazards!
Wear gloves!
268249EF
2011-07-14
1/8

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 284 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for VAT 284 Series

  • Page 1 Read these «Installation, Operating & Maintenance Instructions» and the enclosed «General Safety Instructions» carefully before you start any other action! VAT Vakuumventile AG, CH-9469 Haag, Switzerland 268249EF Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com...
  • Page 2 VAT products. The VAT firmware contains a limited, time unlimited user license. The VAT firmware may not be used for purposes other than those intended nor is it permitted to make copies of the VAT firmware. In particular, it is strictly forbidden to give copies of the VAT firmware to other people.
  • Page 3 4.1.3 Installation of "actuator/gate assembly" ....................7 5 Drawing..................................7 6 Spare parts ................................8 7 Warranty ................................... 8 VAT Vakuumventile AG, CH-9469 Haag, Switzerland 268249EF Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com 2011-07-14...
  • Page 4 (ID 5/8”, 1”, 1½”, 2½”) Use of product Use product for clean and dry indoor vacuum applications under the conditions indicated in chapter «Technical data» only! Other applications are only allowed with the written permission of VAT. Technical data for standard valve ≤ 5...
  • Page 5 1“ 1½ 2½ A combination of both forces «F » and «M» is prohibited. Please contact VAT. Operation Normal operation The valve is fully open when the green marking on the spindle is visible. Operation under increased temperature See «1.1 Technical data»...
  • Page 6 Contamination from the process may influence the function and requires more frequent maintenance. Before carrying out any maintenance or repairs, please contact VAT. It has to be individually decided whether the maintenance/repair can be performed by the customer or has to be carried out by VAT. The fabrication number on the valve made in Switzerland Fabrication No.:...
  • Page 7 • Perform function and leak test Drawing 1) Please make sure that the bonnet seal is mounted like shown. VAT Vakuumventile AG, CH-9469 Haag, Switzerland 268249EF Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com...
  • Page 8 (including any delay in or failure to deliver), packaging, storage or use of any product sold or delivered by VAT shall fail to conform to the...

This manual is also suitable for:

285 seriesDn 16Dn 25Dn 40Dn 63

Table of Contents