VAT 10.8 Series Installation, Operating, & Maintenance Instructions
Uhv gate valve with pneumatic actuator dn 63 - 200 (2 1/2" - 8")
Hide thumbs
Also See for 10.8 Series:
Table of Contents
Advertisement
UHV gate valve
with pneumatic actuator
This manual is valid for the valve ordering number(s):
10836- . E14/24/34/44
10840- . E14/24/34/44
10844- . E14/24/34/44
10846- . E14/24/34/44
The fabrication number is indicated on each product as per the label
below (or similar):
made in Switzerland
Fabrication No.:
patented
10 . . . – . . . . – . . . . / . . . .
A – . . . . . .
Explanation of symbols:
Read declaration carefully before you start any other
action!
Attention!
Product is in conformity with EC guidelines,
if applicable!
Disconnect electrical power and compressed air
lines. Do not touch parts under voltage!
Read these «Installation, Operating & Maintenance Instructions» and the enclosed «General
Safety Instructions» carefully before you start any other action!
VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com
Installation, Operating & Maintenance Instructions
Series 10.8, DN 63 - 200 (2½" - 8")
. .
Fabrication number
Keep body parts and objects away from the valve
opening!
Hot surfaces; do not touch!
Loaded springs and/or air cushions are potential
hazards!
Wear gloves!
205841ED
2008-01-26
1/14
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VAT 10.8 Series
Summary of Contents for VAT 10.8 Series
- Page 1 Do not touch parts under voltage! Read these «Installation, Operating & Maintenance Instructions» and the enclosed «General Safety Instructions» carefully before you start any other action! VAT Vakuumventile AG, CH-9469 Haag, Switzerland 205841ED 1/14 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com...
- Page 2 VAT products. The VAT firmware contains a limited, time unlimited user license. The VAT firmware may not be used for purposes other than those intended nor is it permitted to make copies of the VAT firmware. In particular, it is strictly forbidden to give copies of the VAT firmware to other people.
-
Page 3: Table Of Contents
5.2 Replacement of gate ............................10 6 Drawing................................... 11 7 Spare parts ................................12 8 Warranty ................................. 14 VAT Vakuumventile AG, CH-9469 Haag, Switzerland 205841ED 3/14 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com... -
Page 4: Use Of Product
Series 10.8, DN 63 - 200 (2½" - 8") Use of product Use product for clean and dry indoor vacuum applications under the conditions indicated in chapter «Technical data» only! Other applications are only allowed with the written permission of VAT. Technical data Pressure range 1 x 10 mbar to 1.6 bar (abs) -
Page 5: Connections
MV = coil of solenoid MV = coil of solenoid Minimum pulse duration 50 ms Continuous voltage does not damage the coil VAT Vakuumventile AG, CH-9469 Haag, Switzerland 205841ED 5/14 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com... -
Page 6: Operation
Behavior in case of other failures Standard solenoid: valve closes Solenoid for impulse actuation (option): valve position does not change, but a started movement will be completed VAT Vakuumventile AG, CH-9469 Haag, Switzerland 205841ED 6/14 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com... -
Page 7: Trouble Shooting
DN200; 40 Nm / 30 lbf . ft. If you need any further information, please contact one of our service centers. You can find the addresses on our website: http://www.vat.ch VAT Vakuumventile AG, CH-9469 Haag, Switzerland 205841ED 7/14 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com... -
Page 8: Maintenance & Repairs
Contamination from the process may influence the function and requires more frequent maintenance. Before carrying out any maintenance or repairs, please contact VAT. It has to be individually decided whether the maintenance/repair can be performed by the customer or has to be carried out by VAT. The fabrication number on the valve made in Switzerland Fabrication No.:... -
Page 9: Replacement Of Actuator / Mechanism Assembly
Torque: DN 63 - 160 DN 200 40 Nm / 30 lbf . ft Body Adhesive tape Bonnet seal Bonnet VAT Vakuumventile AG, CH-9469 Haag, Switzerland 205841ED 9/14 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com 2008-01-26... -
Page 10: Replacement Of Gate
- Remove tool (W1) - Check whether gate is properly inserted. The markings ∆ and ∇ (W2) of ball guidance and gate must face each other. VAT Vakuumventile AG, CH-9469 Haag, Switzerland 205841ED 10/14 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com... -
Page 11: Drawing
Installation, Operating & Maintenance Instructions Series 10.8, DN 63 - 200 (2½" - 8") Drawing VAT Vakuumventile AG, CH-9469 Haag, Switzerland 205841ED 11/14 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com 2008-01-26... -
Page 12: Spare Parts
Solenoid kit 94801-R1 43/1 Solenoid N-7557-018 *) 43/1 Solenoid N-7557-021 *) 43/10 Plug N-8501-400 43/10 Plug N-8501-400 VAT Vakuumventile AG, CH-9469 Haag, Switzerland 205841ED 12/14 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com 2008-01-26... - Page 13 Size of valve Qty. Part No. DN 63 67484-R1 DN 100 67483-R1 DN 160 67482-R1 DN 200 67482-R1 VAT Vakuumventile AG, CH-9469 Haag, Switzerland 205841ED 13/14 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com 2008-01-26...
-
Page 14: Warranty
(including any delay in or failure to deliver), packaging, storage or use of any product sold or delivered by VAT shall fail to conform to the...
Need help?
Do you have a question about the 10.8 Series and is the answer not in the manual?
Questions and answers